この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の開発に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2. www.iso.org/directives
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受け取った特許宣言の ISO リストに記載されます。 www.iso.org/patents
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
この文書を担当する委員会は、ISO/TC 27, 固体鉱物燃料、小委員会 SC 5, 分析方法です。
この第 2 版は、第 1 版 (ISO 11722:1999) を取り消して置き換えるものであり、そのマイナー リビジョンを構成します。
序章
一般的な分析試験サンプル中の水分の決定は、特定の分析的決定の結果、例えば揮発性物質および水素、決定における水の影響を修正し、すべての決定を乾物基準に修正できるようにするために必要です。
硬炭は吸湿性があるため、大気中の湿度の変化により水分が変化するため、一般分析試験試料中の水分は、他の分析測定のために部分を秤量するたびに測定する必要があります。いくつかの分析測定用の試験片を同時に秤量する場合、これらの分析を修正するには、1 回の同時水分測定で十分です。
1 スコープ
この規格は、硬質炭の一般分析試験試料中の水分を窒素中で乾燥して測定する方法を規定しています。
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 1213-2, 固体鉱物燃料 — 語彙 — 2: サンプリング、試験、分析に関する用語
3 用語と定義
このドキュメントの目的のために、ISO 1213-2 に記載されている用語と定義が適用されます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
The committee responsible for this document is ISO/TC 27, Solid mineral fuels, Subcommittee SC 5, Methods of analysis.
This second edition cancels and replaces the first edition (ISO 11722:1999), of which it constitutes a minor revision.
Introduction
The determination of the moisture in the general analysis test sample is required to correct the results of certain analytical determinations, e.g. volatile matter and hydrogen, for the effect of water in the determination and to allow all determinations to be corrected to dry basis.
Since hard coal is hygroscopic, its moisture will vary with change of humidity of the atmosphere and the moisture in the general analysis test sample should therefore be determined whenever portions are weighed out for other analytical determinations. If test portions for several analytical determinations are weighed out at the same time, a single simultaneous moisture determination will suffice to correct those analyses.
1 Scope
This International Standard specifies a method for determining the moisture in the general analysis test sample of hard coal by drying in nitrogen.
2 Normatives references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 1213-2, Solid mineral fuels — Vocabulary — 2: Terms relating to sampling, testing and analysis
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1213-2 apply.