※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令、 Part 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
適合性評価に関連する ISO 固有の用語および表現の意味に関する説明、および技術的貿易障壁 (TBT) における WTO 原則への ISO の準拠に関する情報については、次の URL を参照して ください 。
この文書を担当する委員会は、ISO/TC 160, 建物内のガラス、小委員会 SC 2, 技術委員会 CEN/TC 129, 建物内のガラスと連携した使用に関する考慮事項です。
ISO 1288 は、次の部分で構成されており、一般的なタイトルは「建物のガラス - ガラスの曲げ強度の決定」の下にあります。
- Part 1: ガラスの試験の基礎
- Part 2: 大きな試験表面積を持つ平らな試験片での同軸二重リング試験
- Part 3: 試験片を 2 点で支えた状態でのテスト(4 点曲げ)
- Part 4: チャネル型ガラスのテスト
- Part 5: 試験表面積が小さい平らな試験片での同軸二重リング試験
この国際規格は、EN 1288-5, 建物内のガラス — ガラスの曲げ強度の決定 — Part 5 部:技術委員会 CEN/TC 129「Glass建物内」。
CEN/CENELEC 内部規則によると、次の国の国家標準化組織がこの欧州標準を実装する義務があります: オーストリア、ベルギー、チェコ共和国、デンマーク、フィンランド、フランス、ドイツ、ギリシャ、アイスランド、アイルランド、イタリア、ルクセンブルク、オランダ、ノルウェー、ポルトガル、スペイン、スウェーデン、スイス、イギリス。
1 スコープ
ISO 1288 のこの部分では、エッジの影響を除いて、建物で使用するガラスの比較曲げ強度を決定する方法を指定しています。
この試験方法がガラスの種類の強度を比較するためにのみ使用されるべきであり、設計目的で強度を評価するために使用されるべきではない理由については、ISO 1288-1, 5.1.4 を参照してください。
ISO 1288 のこの部分の制限は、ISO 1288-1 で説明されています。
ISO 1288-1 は、ISO 1288 のこの部分と併せて読む必要があります。
この試験方法は模様付きガラスには適していません。
2 参考文献
以下のドキュメントの全体または一部は、このドキュメントで規範的に参照されており、その適用に不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 48, ゴム、加硫または熱可塑性 — 硬度の測定 (10 IRHD と 100 IRHD の間の硬度)
3 用語と定義
このドキュメントでは、次の用語と定義が適用されます。
3.1
曲げ応力
試験片の表面に生じる引張り曲げ応力
注記 1:試験目的のため、曲げ応力は表面の指定された部分で均一でなければなりません。
参考文献
| [1] | ISO 1288-1, 建物内のガラス — ガラスの曲げ強度の決定 — Part 1: ガラス試験の基礎 |
| [2] | ISO 16293-1, 建物のガラス - 基本的なソーダ石灰ケイ酸塩ガラス製品 - Part 1: 定義と一般的な物理的および機械的特性 |
| [3] | Schmitt RW, Blank K.、Schönbrunn G.、二重リング法の実験的応力解析; Talking Room 116 (1983), No.5, pp.397-405 および Talking Room 116 (1983), No.8, p669 の誤字修正 |
| [4] | Kerkhof F.、ガラスの破損プロセス。 (ガラスの破砕プロセス。) ; Deutsche Glastechnische Gesellschaft, フランクフルト/マイン、1970 年、p. 209ff |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 160, Glass in building, Subcommittee SC 2, Use considerations in conjunction with Technical Committee CEN/TC 129, Glass in building.
ISO 1288 consists of the following parts, under the general title Glass in building — Determination of the bending strength of glass:
- Part 1: Fundamentals of testing glass
- Part 2: Coaxial double-ring test on flat specimens with large test surface areas
- Part 3: Test with specimen supported at two points(four-point bending)
- Part 4: Testing of channel-shaped glass
- Part 5: Coaxial double-ring test on flat specimens with small test surface areas
This International Standard has been based on EN 1288-5, Glass in building — Determination of the bending strength of glass — Part 5: Coaxial double-ring test on flat specimens with small test surface areas prepared by Technical Committee CEN/TC 129 “Glass in building”.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
1 Scope
This part of ISO 1288 specifies a method for determining the comparative bending strength of glass for use in buildings, excluding the effects of the edges.
See ISO 1288-1, 5.1.4 for an explanation as to why this test method should only be used for comparing the strength of types of glass and not for assessing strength for design purposes.
The limitations of this part of ISO 1288 are described in ISO 1288-1.
ISO 1288-1 should be read in conjunction with this part of ISO 1288.
This test method is not suitable for patterned glass.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and 100 IRHD)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
bending stress
tensile bending stress induced in the surface of a specimen
Note 1 to entry: For testing purposes, the bending stress should be uniform over a specified part of the surface.
Bibliography
| [1] | ISO 1288-1, Glass in building — Determination of the bending strength of glass — Part 1: Fundamentals of testing glass |
| [2] | ISO 16293-1, Glass in building — Basic soda lime silicate glass products — Part 1: Definitions and general physical and mechanical properties |
| [3] | Schmitt R.W., Blank K., Schönbrunn G., Experimentelle Spannungsanalyse zum Doppelringverfahren (Experimental stress analysis for the double ring method); Sprechsaal 116 (1983), No.5, pp.397-405 and printing error correction in Sprechsaal 116 (1983),No.8, p669 |
| [4] | Kerkhof F., Bruchvorgange in Gläsern. (Fracture Processes in Glass.); Deutsche Glastechnische Gesellschaft, Frankfurt/Main 1970, p. 209 ff |