※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
技術委員会によって採択された国際規格草案は、投票のために加盟団体に回覧されます。国際規格として発行するには、投票を行った加盟団体の少なくとも 75% による承認が必要です。
国際規格 ISO 13774 は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 1, ホース (ゴムおよびプラスチック) によって作成されました。
警告 — この国際規格を使用する人は、通常の実験室での実践に精通している必要があります。この規格は、その使用に関連する安全上の問題があったとしても、そのすべてに対処することを目的とするものではありません。適切な安全衛生慣行を確立し、国の規制条件を確実に遵守することはユーザーの責任です。
この国際規格で指定された試験が適切な環境条件下で実施されること、および火災の危険や煙および/または有毒な燃焼生成物の吸入の危険から人員が適切に保護されていることを保証する必要性に注意が払われます。
1 スコープ
この国際規格は、内燃機関用の石油燃料での使用を目的とした、公称口径 16 以下のホースの可燃性を評価する方法を規定しています。
注 –他のタイプのゴムおよびプラスチックホースの可燃性試験方法は、ISO 8030:1995 「ゴムおよびプラスチックホース – 可燃性試験方法」に記載されています。
2 基準参照
以下の規格には、本文中の参照を通じてこの国際規格の条項を構成する条項が含まれています。発行時点では、示されているエディションは有効です。すべての規格は改訂される可能性があり、この国際規格に基づく協定の当事者は、以下に示す規格の最新版を適用する可能性を調査することが推奨されます。 IEC および ISO のメンバーは、現在有効な国際規格の登録簿を維持しています。
- ISO 471:1995, ゴム - 温度、湿度、調整とテストの時間。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard ISO 13774 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics).
WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions.
Attention is drawn to the need for ensuring that the test specified in this International Standard is carried out under suitable environmental conditions and that personnel are adequately protected against risk of fire and inhalation of smoke and/or toxic products of combustion.
1 Scope
This International Standard specifies a method for assessing the flammability of hoses with a nominal bore of 16 or smaller, intended for use with petroleum fuels for internal-combustion engines.
NOTE — The method of test for flammability of other types of rubber and plastics hoses is given in ISO 8030:1995, Rubber and plastics hoses — Method of test for flammability.
2 Normative reference
The following standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the edition indicated was valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent edition of the standard indicated below. Members of IEC and ISO maintain registers of currently valid International Standards.
- ISO 471:1995, Rubber — Temperatures, humidities and times for conditioning and testing.