ISO 13943:2023 火災安全 — 用語、語彙 | ページ 2

この規格 プレビューページの目次

※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。

序文

非推奨:書き込み速度

非推奨:書き込み速度

指定された条件下で単位時間あたりに 燃焼する物質の面積 (3.38)

非推奨:自然発火

内部発熱反応によって引き起こされる 発火 (3.242)

非推奨:自己発火温度

火災試験 (3.180) で 自己発火 (3.27) が得られる最低温度

非推奨: ppm

非推奨:体積ppm

所定の体積に分散または溶解した物質の質量

非推奨:書き込み速度

非推奨:書き込み速度

指定された条件下で、 火炎面 (3.187) が伝播中に移動した距離を移動時間で割ったもの

非推奨:可燃性

指定された条件下で材料または製品が 炎 (3.184 ) で燃える能力 (3.38)

3,201

可燃限界

非推奨:可燃性

指定された条件下で 有炎燃焼が可能 (3.197)

3,203

フラッシュ発火温度

非推奨:発熱量

非推奨:発熱量

与えられた物質の単位質量の 燃焼 (3.62) によって生成される熱エネルギー

非推奨:書き込み速度

非推奨:書き込み速度

燃焼によって生成される熱エネルギー生成率 (3.62)

非推奨:持続点火

<一般> 燃焼の開始 (3.62)

3,243

点火

非推奨:持続点火

非推奨:書き込み速度

非推奨:書き込み速度

指定された条件下で単位時間あたりに 燃焼する物質の長さ (3.38)

非推奨:書き込み速度

非推奨:書き込み速度

指定された条件下で単位時間あたりに 燃焼する物質の質量 (3.38)

非推奨:持続点火

規定の期間を超えて持続する 試験片 (3.428) の 燃焼 (3.62)

非推奨:持続点火

炎 (3.184) 、 試験片 (3.428) の表面上または表面上で、規定の時間以上持続するもの

非推奨: ppm

非推奨:体積ppm

<混合ガス中のガス> 定義された温度と圧力でガスのみが占める体積と、同じ温度と圧力で混合ガスが占める体積の比

注記 1:温度T および圧力P におけるガスの 濃度 (3.69) は 、その体積分率に (理想的なガスの挙動を仮定して) におけるガスの密度を乗算することによって、その体積分率から計算できます。あの温度と圧力。

注記 2: 特に明記されていない限り、温度 298 K, 圧力 1 atm が想定されます。

注記 3:体積分率は無次元であり、通常、μl/l (= cm 3/m 3 = 10 -6 ) またはパーセントで表されます。

3,474

体積収量

298 K, 1 atm における 火災流出物成分の体積 (3.147) を、その体積の生成に伴う 試験片の質量損失 (3.428) で割ったもの。

注記 1:一般的な単位は m 3 ⋅g −1です。

3,475

波数

電磁放射の波長λの逆数 (3.359)

注1:​​ν/λ = 1ここで, ν (波数)は逆センチメートル(cm -1 )で表され、 λは通常μmで表されます。これには、波長から波数を計算する際に 10,000 µm/cm の数値変換係数が必要になります。

3,476

吸湿性のある

毛細管現象による、粒子状または繊維状の物質を通る、またはその上の液体の伝達

3,477

原野火災

森林、低木地、草地または放牧地で発生する、自然起源または人間の介入によって引き起こされる 火災 (3.140)

注記 1:この用語は主に北米で使用されますが、それに限定されるわけではありません。

注記 2:オーストラリア、ニュージーランドおよび南アフリカで使用される 森林火災 (3.46) という用語も参照してください (ISO/TR 24188, 3.1.1 を参照)

注記 3:山火事という用語はカナダと米国でも使用されていますが、「野火」ほど頻繁ではありません。

[出典:ISO/TS 19677:2019, 3.3, 修正 — エントリへの注記 1, 2, および 3 が追加されました。]

3,478

荒野と都市のインターフェース

ウィ

建造物やその他の人間開発が原野に隣接または重なっているwhere

[出典:ISO/TS 19677:2019, 3.4]

3,479

収率

燃焼中に生成される 燃焼生成物 (3.64) の質量 (3.62) を 試験片の質量損失 (3.428) で割った値

注記 1:収量は無次元です。

参考文献

1ISO 871:2022, プラスチック — 熱風炉を使用した発火温度の決定
2ISO/TS 5660-5:2020, 火災への反応試験 — 発熱、発煙および質量損失率 — Part 5: 減酸素雰囲気下での発熱率 (コーン熱量計法) および発煙率 (動的測定)
3ISO 6182-7: 2020, 2防火 — 自動スプリンクラー システム — Part 7: 早期抑制高速応答 (ESFR) スプリンクラーの要件と試験方法
4ISO 6707-1:2020, 建築および土木工事 — 語彙 — Part 1: 一般用語
5ISO 8178-4:2020, レシプロ内燃エンジン — 排気ガス測定 — Part 4: さまざまなエンジン アプリケーションの定常状態および過渡テスト サイクル
6ISO 10241-1:2011, 規格内の用語項目 - Part 1: 一般要件と表現例
7ISO/TS 12828-3:2020, 火災ガス分析の検証方法 - Part 3: 研究所間試験に関する考慮事項
8ISO 13785-2:2002, ファサードの火災反応試験 - Part 2: 大規模試験
9ISO 14934-1:2010, 火災試験 — 熱流束計の校正と使用 — Part 1: 一般原則
10ISO 16000-14:2009, 室内空気 — Part 14: 総 (気相および粒子相) ポリ塩化ダイオキシン様ビフェニル (PCB) およびポリ塩化ジベンゾ-p-ダイオキシン/ジベンゾフラン (PCDD/PCDF) の測定 — 抽出、クリーン高分解能ガスクロマトグラフィーと質量分析による分析
11ISO /TR 16312-2:2021, 火災の危険性およびリスク評価のための火災流出物の毒性データを取得するための物理的火災モデルの妥当性を評価するためのガイダンス — Part 2: 個々の物理的火災モデルの評価
12ISO/TR 16576:2017, 防火工学 - 防火目標、機能要件、安全基準の例
13ISO/TS 16733-2:2021, 防火工学 — 設計火災シナリオと設計火災の選択 — Part 2: 設計火災
14ISO/TR 17252:2019, 火災試験 — 火災試験に対する反応の火災モデリングおよび火災安全工学への適用性
15ISO/TR 17755:2014, 火災安全 — 国内火災統計慣行の概要
16ISO/TS 19677:2019, 環境暴露による原野火災の環境および人々への悪影響を評価するためのガイドライン
17ISO 20414:2020, 火災安全工学 — 火災避難モデルを構築するための検証および検証プロトコル
18ISO 23932-1:2018, 防火工学 — 一般原則 — Part 1: 一般
19ISO/TR 24188:2022, 大規模な屋外火災と建築環境 — 標準化へのさまざまなアプローチの世界的な概要
20ISO 24678-7:2019, 防火工学 — 代数式を管理する要件 — Part 7: 屋外プール火災から受ける放射熱流束
21ISO 24679-1:2019, 防火工学 — 火災における構造物の性能 — Part 1: 一般
22ISO/TR 24679-4:2017, 防火工学 — 火災時の構造物の性能 — Part 4: 15 階建て鉄骨オフィスビルの例
23ISO 26367-1:2019, 火災廃液の環境への悪影響を評価するためのガイドライン — Part 1: 一般
24ISO 26367-2:2017, 火災流出物の環境への悪影響を評価するためのガイドライン — Part 2: 火災による環境に重大な排出物に関するデータを編集するための方法論
25ISO 29903-1:2020, さまざまなテストによる有毒ガスデータの比較 — Part 1: ガイダンスと要件
26ISO/IEC Guide 98-3:2008, 測定の不確かさ — Part 3: 測定における不確かさの表現に関するガイド (GUM:1995)
27ASTM E176:2021, 防火基準の標準用語
28EN 16733:2021, 建築製品の耐火試験に対する反応 - 連続くすぶりを受ける建築製品の傾向の測定
29欧州連合、危険物質が関与する重大事故の危険性の管理に関する 1996 年 12 月 9 日の理事会指令 96/82/E EU理事会、1996年。
30NFPA 用語集、全米防火協会、米国マサチューセッツ州クインシー、2021 年

Foreword

DEPRECATED:burning rate

DEPRECATED:rate of burning

area of material burned (3.38) per unit time under specified conditions

DEPRECATED:spontaneous combustion

ignition (3.242) caused by an internal exothermic reaction

DEPRECATED:self-ignition temperature

minimum temperature at which auto-ignition (3.27) is obtained in a fire test (3.180)

DEPRECATED:ppm

DEPRECATED:ppm by volume

mass of a dispersed or dissolved material in a given volume

DEPRECATED:burning rate

DEPRECATED:rate of burning

distance travelled by a flame front (3.187) during its propagation, divided by the time of travel, under specified conditions

DEPRECATED:inflammability

ability of a material or product to burn (3.38) with a flame (3.184) under specified conditions

3.201

flammability limit

DEPRECATED:inflammable

capable of flaming combustion (3.197) under specified conditions

3.203

flash-ignition temperature

DEPRECATED:calorific potential

DEPRECATED:calorific value

thermal energy produced by combustion (3.62) of unit mass of a given substance

DEPRECATED:burning rate

DEPRECATED:rate of burning

rate of thermal energy production generated by combustion (3.62)

DEPRECATED:sustained ignition

<general> initiation of combustion (3.62)

3.243

ignition

DEPRECATED:sustained ignition

DEPRECATED:burning rate

DEPRECATED:rate of burning

length of material burned (3.38) per unit time under specified conditions

DEPRECATED:burning rate

DEPRECATED:rate of burning

mass of material burned (3.38) per unit time under specified conditions

DEPRECATED:sustained ignition

combustion (3.62) of a test specimen (3.428) which persists for longer than a defined period of time

DEPRECATED:sustained ignition

flame (3.184) , on or over the surface of a test specimen (3.428) , which persists for longer than a defined period of time

DEPRECATED:ppm

DEPRECATED:ppm by volume

<gas in a gas mixture> ratio of the volume that the gas alone would occupy at a defined temperature and pressure, to the volume occupied by the gas mixture at the same temperature and pressure

Note 1 to entry: The concentration (3.69) of a gas at a temperature, T, and a pressure, P, can be calculated from its volume fraction (assuming ideal gas behaviour) by multiplying the volume fraction by the density of the gas at that temperature and pressure.

Note 2 to entry: Unless stated otherwise, a temperature of 298 K and a pressure of 1 atm are assumed.

Note 3 to entry: The volume fraction is dimensionless and is usually expressed in terms of µl/l (= cm3/m3 = 10−6), or as a percentage.

3.474

volume yield

volume, at 298 K and 1 atm, of a component of fire effluent (3.147) divided by the mass loss of the test specimen (3.428) associated with the production of that volume

Note 1 to entry: The typical unit is m3⋅g−1.

3.475

wave number

inverse of the wavelength, λ, of electromagnetic radiation (3.359)

Note 1 to entry:ν/λ = 1 ここで,ν (wave number) is expressed in reciprocal centimetres (cm−1) and λ is normally expressed in μm. This entails a numerical conversion factor of 10 000 µm/cm in the calculation of wave number from wavelength.

3.476

wicking

transmission of a liquid through or over a particulate or fibrous material by capillary action

3.477

wildland fire

fire (3.140) occurring in forests, scrublands, grasslands or rangelands, either of natural origin or caused by human intervention

Note 1 to entry: This term is used primarily, but not exclusively, in North America.

Note 2 to entry: See also the term bushfire (3.46) , used in Australia, New Zealand and South Africa (See ISO/TR 24188, 3.1.1).

Note 3 to entry: The termwildfire is used in Canada and the US, but less frequently than “wildland fire”.

[SOURCE:ISO/TS 19677:2019, 3.3, modified — Notes 1, 2 and 3 to entry have been added.]

3.478

wildland-urban interface

WUI

area where structures and other human developments adjoin or overlap with wildland

[SOURCE:ISO/TS 19677:2019, 3.4]

3.479

yield

mass of a combustion product (3.64) generated during combustion (3.62) divided by the mass loss of the test specimen (3.428)

Note 1 to entry: The yield is dimensionless.

Bibliography

1ISO 871:2022, Plastics — Determination of ignition temperature using a hot-air furnace
2ISO/TS 5660-5:2020, Reaction-to-fire tests — Heat release, smoke production and mass loss rate — Part 5: Heat release rate (cone calorimeter method) and smoke production rate (dynamic measurement) under reduced oxygen atmospheres
3ISO 6182-7:2020, 2Fire protection — Automatic sprinkler systems — Part 7: Requirements and test methods for early suppression fast response (ESFR) sprinklers
4ISO 6707-1:2020, Buildings and civil engineering works — Vocabulary — Part 1: General terms
5ISO 8178-4:2020, Reciprocating internal combustion engines — Exhaust emission measurement — Part 4: Steady-state and transient test cycles for different engine applications
6ISO 10241-1:2011, Terminological entries in standards — Part 1: General requirements and examples of presentation
7ISO/TS 12828-3:2020, Validation method for fire gas analysis — Part 3: Considerations related to interlaboratory trials
8ISO 13785-2:2002, Reaction-to-fire tests for façades — Part 2: Large-scale test
9ISO 14934-1:2010, Fire tests — Calibration and use of heat flux meters — Part 1: General principles
10ISO 16000-14:2009, Indoor air — Part 14: Determination of total (gas and particle-phase) polychlorinated dioxin-like biphenyls (PCBs) and polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDDs/PCDFs) — Extraction, clean-up and analysis by high-resolution gas chromatography and mass spectrometry
11ISO/TR 16312-2:2021, Guidance for assessing the validity of physical fire models for obtaining fire effluent toxicity data for fire hazard and risk assessment — Part 2: Evaluation of individual physical fire models
12ISO/TR 16576:2017, Fire safety engineering — Examples of fire safety objectives, functional requirements and safety criteria
13ISO/TS 16733-2:2021, Fire safety engineering — Selection of design fire scenarios and design fires — Part 2: Design fires
14ISO/TR 17252:2019, Fire tests — Applicability of reaction to fire tests to fire modelling and fire safety engineering
15ISO/TR 17755:2014, Fire safety — Overview of national fire statistics practices
16ISO/TS 19677:2019, Guidelines for assessing the adverse impact of wildland fires on the environment and to people through environmental exposure
17ISO 20414:2020, Fire safety engineering — Verification and validation protocol for building fire evacuation models
18ISO 23932-1:2018, Fire safety engineering — General principles — Part 1: General
19ISO/TR 24188:2022, Large outdoor fires and the built environment — Global overview of different approaches to standardization
20ISO 24678-7:2019, Fire safety engineering — Requirements governing algebraic formulae — Part 7: Radiation heat flux received from an open pool fire
21ISO 24679-1:2019, Fire safety engineering — Performance of structures in fire — Part 1: General
22ISO/TR 24679-4:2017, Fire safety engineering — Performance of structures in fire — Part 4: Example of a fifteen-storey steel-framed office building
23ISO 26367-1:2019, Guidelines for assessing the adverse environmental impact of fire effluents — Part 1: General
24ISO 26367-2:2017, Guidelines for assessing the adverse environmental impact of fire effluents — Part 2: Methodology for compiling data on environmentally significant emissions from fires
25ISO 29903-1:2020, Comparison of toxic gas data from different tests — Part 1: Guidance and requirements
26ISO/IEC Guide 98-3:2008, Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)
27ASTM E176:2021, Standard Terminology of Fire Standards
28EN 16733:2021, Reaction to fire tests for building products - Determination of a building product’s propensity to undergo continuous smouldering
29EUROPEAN UNION, Council Directive 96/82/EC of 9 December 1996 on the control of major-accident hazards involving dangerous substances. EU Council, 1996.
30NFPA Glossary of Terms, National Fire Protection Association, Quincy, MA, USA, 2021