この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令で指定された規則に従って起草されます。 2.
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
ISO 14400 は、技術委員会 ISO/TC 22, 道路車両、小委員会 SC 19, ホイールによって作成されました。
序章
この国際規格の目的は、道路車両の安全な操作を確保することです。ホイールは非常にストレスのかかる車両部品であり、使用中に極端な力を受ける可能性があります。したがって、これらの部品の取り扱いには細心の注意を払い、安全な操作とサービス事故を防止するために、取り付け、取り外し、およびメンテナンスに特に注意を払う必要があります。
1 スコープ
この国際規格は、ホイールとリムの使用、一般的なメンテナンス、および安全性に関する要件を指定し、ひび割れ、摩耗、および曲がったホイールなどの非使用状態を定義します。 ISO 3833 で定義されているように、モペットとオートバイを除き、トラック用のマルチピース ホイールを含む道路車両での使用を意図したホイールに適用されます。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
3 用語と定義
このドキュメントの目的のために、ISO 3911 に記載されている用語と定義が適用されます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14400 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 19, Wheels.
Introduction
The purpose of this International Standard is to ensure the safe operation of road vehicles. The wheel is a highly stressed component of the vehicle that may be subject in service to extreme forces. Therefore, it is absolutely necessary to handle these parts with care and to pay particular attention to their mounting, removal and maintenance in order to ensure safe operations and to prevent servicing accidents.
1 Scope
This International Standard specifies requirements for the use, and general maintenance and safety of wheels and rims, and defines their out-of-service conditions, such as cracked, worn and bent wheels. It is applicable to wheels intended for use on road vehicles as defined in ISO 3833, excepting mopeds and motorcycles, and including multi-piece wheels for trucks.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 3833, Road vehicles — Types — Terms and definitions
- ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 3911 apply.