この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序章
写真フィルムおよび写真用紙は、一時的または可逆的な寸法変化と永久的な寸法変化を示します。この国際規格は、試験片を処理するための統一された方法を提供し、大気条件の変化に伴って発生する寸法変化、および加工と老化で発生する寸法変化を表現するために設計されています。
一時的または可逆的な寸法変化は、平衡含水量 (周囲の大気の相対湿度によって決定される) の変化または温度の変化の結果です。加工や経年劣化により、恒久的な寸法変化が生じます。フィルムの永久収縮率は一般に温度とともに増加しますが、時間とともに減少します。収縮率は、フィルムの種類に応じて、相対湿度が高い場合と低い場合のどちらでも最大になる場合があります。一部の素材、特にポリエステル ベースの写真フィルムは、高湿度にさらされた後に膨潤を示すことがあります。
近年、寸法安定性が重要な用途での写真フィルムの使用の増加により、寸法特性の正確な測定の重要性が強調されています。例えば、写真製版では、わずか 0.01% の寸法変化が実用上重要な場合があります。空中マッピングの場合、倍率を変更することで簡単に修正できるため、均一な収縮は深刻ではありませんが、2 つの主な方向の収縮の違いはエラーの原因となります。寸法の局所的または不均一な変化は、実用上の懸念事項です。
フィルムや紙の寸法変化特性は、組成や製造方法だけでなく、熱や水分の履歴にも依存します。このような特性を正確に評価するには、試料の履歴をある程度管理するだけでなく、コンディショニングと測定手順を非常に正確に管理する必要があります。フィルムと紙の寸法もヒステリシスの影響を受けます。これらは、ポリエステル写真ベースフィルムなどのより安定した材料では比較的重要です。
写真フィルムと写真用紙の寸法特性、および測定方法に関する追加情報は、参考文献に記載されています。
Introduction
Photographic films and papers exhibit temporary or reversible dimensional changes as well as permanent dimensional changes. This International Standard is designed to provide uniform methods for treating the specimens and for expressing the dimensional changes which occur with changes in atmospheric conditions and those which occur in processing and ageing.
Temporary or reversible dimensional changes are the result of changes in the equilibrium moisture content (which is determined by the relative humidity of the surrounding atmosphere) or changes in temperature. Permanent dimensional changes occur as the result of processing and ageing. The rate of permanent shrinkage of film generally increases with temperature, but decreases with time. The rate of shrinkage may also be greatest at either high or low relative humidity, depending on the type of film. Some materials, particularly photographic film on polyester base, can show a swelling after a high humidity exposure.
The increasing use of photographic films in recent years, in applications where dimensional stability is critical, has emphasized the importance of an accurate measure of dimensional properties. For example, in photomechanical reproductions a dimensional change of as little as 0,01 % may be of practical importance. In the case of aerial mapping, uniform shrinkage is not serious since it can be easily corrected by a change in magnification, but any difference in shrinkage in the two principal directions is a source of error. Any localized or non-uniform changes in dimension are of practical concern.
The dimensional change properties of any film or paper depend not only on their composition and method of manufacture, but also on their thermal and moisture content history. Accurate evaluation of such properties requires some control over the specimen history as well as very precise control over the conditioning and measuring procedures. Film and paper dimensions are also subject to hysteresis effects. These are relatively more important with the more stable materials such as polyester photographic base films.
Additional information on the dimensional characteristics of photographic films and papers and on methods of measurement may be found in the bibliography.