この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
3 用語と定義
このドキュメントでは、次の用語と定義が適用されます。
3.1
申請手順書
APS
コーティング塗布に使用される手順、方法、機器およびツールを説明する文書
3.2
アプリケーター
ISO 21809 のこのパートに従って塗装を行う会社
3.3
バッチ
8 時間以下の連続生産運転中に、同じ配合と同じソースの原材料を使用して製造されたエポキシ粉末の量。
3.4
バッチ証明書
メーカー発行の分析証明書
3.5
減らす
接合目的で両端をコーティングされていないパイプの長さ
3.6
ガラス転移
非晶質ポリマーまたは部分的に結晶性のポリマーの非晶質領域における、粘性またはゴム状の状態から、硬くて比較的脆い状態への (またはその状態への) 可逆的変化。
[出典:ISO 11357-2:2013, 3.1]
3.7
ガラス転移温度
Tg
ガラス転移が起こる温度範囲の特性値
注記 1:注記: 指定されたガラス転移温度Tgは、特定の特性、およびそれを測定するために選択された方法と条件によって異なります。
[出典:ISO 11357-2:2013, 3.2]
3.8
休日
特定の電圧にさらされると導電性を示すコーティングの不連続性
3.9
実験室でコーティングされた試験片
実験室で準備されたパネルから採取された標本
3.10
メーカー
コーティング材料の製造を担当する会社
3.11
メーカーの仕様
コーティング材料の特性、テスト要件、およびアプリケーションの推奨事項を指定する文書
3.12
粉末出荷
コンテナ1個あたりの粉体輸送量
3.13
手続き資格試験
PQT
APS が指定された特性を備えたコーティングを生成するのに十分であることを確認するための、コーティングの適用とその後のその特性の検査/テスト。生産開始前に実施されます。
3.14
購入者
製品注文要件の提供を担当する会社
3.15
試験報告書
ISO 21809 のこの部分の要件に従って実施されたテストの定量的なテスト結果を提供する文書。
3.16
テストリング
生産コーティングされたパイプから採取されたサンプル
参考文献
| [1] | ISO 3183, 石油および天然ガス産業 — パイプライン輸送システム用鋼管 |
| [2] | ISO 11357-2:2013, プラスチック — 示差走査熱量測定 (DSC) — 2: ガラス転移温度とガラス転移ステップ高さの決定 |
| [3] | ISO 14001, 環境管理システム — 使用に関するガイダンスを含む要件 |
| [4] | ISO/TS 29001, 石油、石油化学および天然ガス産業 — セクター固有の品質管理システム — 製品およびサービス供給組織の要件 |
| [5] | ASTM E29, 試験データで有効数字を使用して仕様への適合性を判断するための標準プラクティス |
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
application procedure specification
APS
document describing procedures, methods, equipment and tools used for coating application
3.2
applicator
company that undertakes the coating application in accordance with this part of ISO 21809
3.3
batch
quantity of epoxy powder produced using the same formulation and raw materials of the same source during a continuous production run of not more than 8 h
3.4
batch certificate
certificate of analysis issued by the manufacturer
3.5
cutback
length of pipe left uncoated at each end for joining purposes
3.6
glass transition
reversible change in an amorphous polymer or in amorphous regions of a partially crystalline polymer from (or to) a viscous or rubbery condition to (or from) a hard and relatively brittle one
[SOURCE:ISO 11357‑2:2013, 3.1]
3.7
glass transition temperature
Tg
characteristic value of the temperature range over which the glass transition takes place
Note 1 to entry: Note to entry: The assigned glass transition temperature, Tg, can vary, depending on the specific property and on the method and conditions selected to measure it.
[SOURCE:ISO 11357‑2:2013, 3.2]
3.8
holiday
coating discontinuity that exhibits electrical conductivity when exposed to a specific voltage
3.9
laboratory-coated test specimen
specimen taken from a laboratory-prepared panel
3.10
manufacturer
company responsible for the manufacture of coating material(s)
3.11
manufacturer’s specification
document that specifies the characteristics, test requirements and application recommendations for the coating materials
3.12
powder shipment
amount of powder transported in one container
3.13
procedure qualification trial
PQT
application of a coating and subsequent inspection/testing of its properties, to confirm that the APS is adequate to produce a coating with the specified properties, carried out prior to the start of production
3.14
purchaser
company responsible for providing the product order requirements
3.15
test report
document that provides the quantitative test results for tests conducted in accordance with the requirements of this part of ISO 21809
3.16
test ring
sample taken from production-coated pipe
Bibliography
| [1] | ISO 3183, Petroleum and natural gas industries — Steel pipe for pipeline transportation systems |
| [2] | ISO 11357-2:2013, Plastics — Differential scanning calorimetry (DSC) — 2: Determination of glass transition temperature and glass transition step height |
| [3] | ISO 14001, Environmental management systems — Requirements with guidance for use |
| [4] | ISO/TS 29001, Petroleum, petrochemical and natural gas industries — Sector-specific quality management systems — Requirements for product and service supply organizations |
| [5] | ASTM E29, Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |