※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令で指定された規則に従って起草されます。 2.
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
このドキュメントの一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
ISO 28702 は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 1, ホース (ゴムおよびプラスチック)によって作成されました。
序章
この国際規格は、ホースの低温特性を試験するために使用でき、それにより、ライニングとカバーに使用される材料の脆性温度を評価できます。
この方法では、試験温度でのホースの柔軟性は測定されません。
ホースおよびホース アセンブリのその他の周囲温度以下の試験は、ISO 4672, ゴムおよびプラスチック ホース - 周囲温度以下の柔軟性試験[ISO 10619-2 (準備中) に置き換え予定] に記載されています。
1 スコープ
この国際規格は、ホースの試験片を粉砕することにより、周囲温度以下で繊維補強材とチューブを備えたゴムおよびプラスチックホースの低温脆性を測定するための試験方法を指定しています。
この国際規格は、公称口径が 100 mm までのホースにのみ適用されます。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 23529, ゴム — 物理的試験方法のための試験片の準備とコンディショニングの一般的な手順
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 28702 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics).
Introduction
This International Standard can be used to test the low-temperature properties of hoses whereby the brittle temperature of materials used for the lining and cover can be assessed.
The method does not measure the flexibility of hoses at the test temperature.
Other sub-ambient temperature tests for hoses and hose assemblies are given in ISO 4672, Rubber and plastics hoses — Sub-ambient temperature flexibility tests [to be replaced by ISO 10619-2 (in preparation)].
1 Scope
This International Standard specifies a test method for measuring the low-temperature brittleness of rubber and plastics hoses with a textile reinforcement and tubing at sub-ambient temperatures by crushing a test piece of the hose.
This International Standard is only applicable to hoses with a nominal bore up to and including 100 mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 23529, Rubber — General procedures for preparing and conditioning test pieces for physical test methods