※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持を意図した手順は、ISO/IEC 指令で説明されています。 1. 特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令の編集規則に従って作成されました。 2 ( www.iso.org/directives を参照)
このドキュメントの一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部またはすべてを特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
規格の自発的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および技術的貿易障壁 (TBT) における世界貿易機関 (WTO) の原則への ISO の準拠に関する情報については、以下を参照してください。 www.iso.org/iso/foreword.html .
この文書は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 1, ゴムおよびプラスチック ホースおよびホース アセンブリによって作成されました。
この第 4 版は、技術的に改訂された第 3 版 (ISO 2928:2003) を取り消して置き換えるものです。
前作からの主な変更点は以下の通り。
- 表 1 および表 2 の公称サイズ 9 を公称サイズ 10 に、公称サイズ 12 を公称サイズ 13 に改名。
- 表 1 に公称サイズ 10 のホースを追加。
- 表 3 に刺されていないホースを追加。
- 箇条 4 のホース/ホース アセンブリ クラスの拡張。
警告このドキュメントを使用する人は、通常の実験室の慣行に精通している必要があります。このドキュメントは、その使用に関連する安全上の問題のすべてに対処することを目的としていません。適切な健康および安全慣行を確立し、国の規制条件を考慮することは、ユーザーの責任です。
1 スコープ
この文書は、液相または気相の液化石油ガス (LPG) および天然ガスの移送に使用され、真空から最大 2.5 MPa ( 25 bar ) −30 °C から +70 °C の温度範囲内、または低温ホース (-LT と指定) の場合は、-50 °C から +70 °C の温度範囲内。
2 参考文献
以下のドキュメントは、その内容の一部またはすべてがこのドキュメントの要件を構成するように、本文で参照されています。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 37, ゴム、加硫または熱可塑性 — 引張応力-ひずみ特性の測定
- ISO 48-2, ゴム、加硫または熱可塑性 — 硬度の測定 — 2: 10 IRHD と 100 IRHD の間の硬度
- ISO 188, ゴム、加硫または熱可塑性 — 加速老化および耐熱性試験
- ISO 1382, ゴム - 語彙
- ISO 1402, ゴムおよびプラスチックホースおよびホースアセンブリ - 静水圧試験
- ISO 1817, ゴム、加硫または熱可塑性 - 液体の影響の測定
- ISO 4649, ゴム、加硫または熱可塑性 — 回転円筒ドラム装置を使用した耐摩耗性の測定
- ISO 4671, ゴムおよびプラスチックホースおよびホースアセンブリ - ホースの寸法およびホースアセンブリの長さの測定方法
- ISO 6179:2017, ゴム、加硫または熱可塑性 — ゴムシートおよびゴム被覆布 — 揮発性液体の透過率の測定 (重量法)
- ISO 7233, ゴムおよびプラスチックホースおよびホースアセンブリ - 吸引抵抗の決定
- ISO 7326, ゴムおよびプラスチックホース - 静的条件下での耐オゾン性の評価
- ISO 8031, ゴムおよびプラスチックホースおよびホースアセンブリ - 電気抵抗および導電率の測定
- ISO 8033, ゴムおよびプラスチックホース - コンポーネント間の接着の測定
- ISO 8330, ゴムおよびプラスチックホースおよびホースアセンブリ — 語彙
- ISO 10619-1, ゴムおよびプラスチックホースおよびチューブ — 柔軟性と剛性の測定 — 1: 常温での曲げ試験
- ISO 10619-2:2017, ゴムおよびプラスチックのホースおよびチューブ — 柔軟性と剛性の測定 — 2: 周囲温度以下での曲げ試験
3 用語と定義
このドキュメントの目的のために、ISO 1382 および ISO 8330 に記載されている用語と定義が適用されます。
ISO と IEC は、次のアドレスで標準化に使用する用語データベースを維持しています。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Rubber and plastics hoses and hose assemblies.
This fourth edition cancels and replaces the third edition (ISO 2928:2003), which has been technically revised.
The main changes compared to the previous edition are as follows:
- renaming of nominal size 9 into nominal size 10 and of nominal size 12 into nominal size 13 in Tables 1 and 2;
- addition of hoses with a nominal size 10 in Table 1;
- addition of non-pricked hoses in Table 3;
- expansion of the hose/hose assembly classes in Clause 4.
WARNING Persons using this document should be familiar with normal laboratory practice. This document does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to consider any national regulatory conditions.
1 Scope
This document specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 2,5 MPa (25 bar) within the temperature range −30 °C to +70 °C or, for low-temperature hoses (designated -LT), within the temperature range −50 °C to +70 °C.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
- ISO 48-2, Rubber, vulcanized or thermoplastic — Determination of hardness — 2: Hardness between 10 IRHD and 100 IRHD
- ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
- ISO 1382, Rubber — Vocabulary
- ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
- ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids
- ISO 4649, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
- ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
- ISO 6179:2017, Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique)
- ISO 7233, Rubber and plastics hoses and hose assemblies — Determination of suction resistance
- ISO 7326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
- ISO 8031, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and conductivity
- ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
- ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
- ISO 10619-1, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — 1: Bending tests at ambient temperature
- ISO 10619-2:2017, Rubber and plastics hoses and tubing — Measurement of flexibility and stiffness — 2: Bending tests at sub-ambient temperatures
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1382 and ISO 8330 apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses: