この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
1 スコープ
1.1 一般
この国際規格は、騒音源の音響パワー レベルまたは音響エネルギー レベルを、残響のある環境に現場で取り付けられた騒音源 (機械または装置) から放出される測定音圧レベルと、校正された基準からの音圧レベルを比較することによって決定する方法を指定します。音源。 1 オクターブ幅の周波数帯域で、騒音源によって生成される音響パワー レベル (または、ノイズ バーストまたはトランジェント ノイズ放出の場合は音響エネルギー レベル) は、これらの測定値を使用して計算されます。周波数 A 特性が適用されたサウンド パワー レベルまたはサウンド エネルギー レベルは、オクターブ バンド レベルを使用して計算されます。
1.2 騒音の種類と騒音源
この国際規格で指定されている方法は、ISO 12001 で定義されているすべてのタイプのノイズ (定常、非定常、変動、孤立した音エネルギーのバーストなど) に適しています。 .ただし、測定の再現性が低下する可能性はありますが、狭帯域ノイズまたは離散トーンを放出するソースにも使用できます。
テスト対象のノイズ源は、デバイス、機械、コンポーネント、またはサブアセンブリ、特に動かないものである可能性があります。
1.3 テスト環境
この国際規格に従って行われる測定に適用できる試験環境は、マイクロホン位置での音圧レベルが主に部屋の表面からの反射に依存する部屋です (4.1 を参照) ISO 12001:1996, 精度グレード 2 (エンジニアリング グレード) の測定では、テスト環境のバックグラウンド ノイズは、ノイズ ソースまたは基準音源のバックグラウンド ノイズと比較して低いです (4.2 を参照)
1.4 測定の不確かさ
この国際規格に従って決定された音響パワーレベルと音響エネルギーレベルの不確実性に関する情報が、オクターブバンドで行われた測定と、オクターブバンドで実行された A 特性周波数計算のために提供されます。不確かさは、テスト環境に関する要件がどの程度満たされているかに応じて、ISO 12001:1996, 精度グレード 2 (エンジニアリング グレード) または ISO 12001:1996, 精度グレード 3 (調査グレード) のいずれかに準拠します。
1 Scope
1.1 General
This International Standard specifies a method for determining the sound power level or sound energy level of a noise source by comparing measured sound pressure levels emitted by a noise source (machinery or equipment) mounted in situ in a reverberant environment, with those from a calibrated reference sound source. The sound power level (or, in the case of noise bursts or transient noise emission, the sound energy level) produced by the noise source, in frequency bands of width one octave, is calculated using those measurements. The sound power level or sound energy level with frequency A-weighting applied is calculated using the octave-band levels.
1.2 Types of noise and noise sources
The method specified in this International Standard is suitable for all types of noise (steady, non-steady, fluctuating, isolated bursts of sound energy, etc.) defined in ISO 12001. The method is primarily applicable to sources which emit broad-band noise. It can, however, also be used for sources which emit narrow-band noise or discrete tones, although there is a possibility that the measurement reproducibility is then degraded.
The noise source under test can be a device, machine, component or sub-assembly, especially one which is non-movable.
1.3 Test environment
The test environment that is applicable for measurements made in accordance with this International Standard is a room where the sound pressure level at the microphone positions depends mainly on reflections from the room surfaces (see 4.1). In measurements of ISO 12001:1996, accuracy grade 2 (engineering grade), background noise in the test environment is low compared to that of the noise source or reference sound source (see 4.2).
1.4 Measurement uncertainty
Information is given on the uncertainty of the sound power levels and sound energy levels determined in accordance with this International Standard, for measurements made in octave bands and for A-weighted frequency calculations performed on them. The uncertainty conforms with that of either ISO 12001:1996, accuracy grade 2 (engineering grade) or ISO 12001:1996, accuracy grade 3 (survey grade), depending on the extent to which the requirements concerning the test environment are met.