この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
3 用語と定義
この文書の目的上、ISO 4437-1, EN 736-1, EN 736-2 および以下に示される用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1 一般
3.1.1
外部気密性
ガスを含む空間を囲むバルブ本体の大気に対する気密性
3.1.2
内部の気密性
バルブが閉位置にあるときの、バルブの入口と出口の間の気密性
3.1.3
漏れ
バルブ本体またはバルブのコンポーネントからのガスの放出
3.1.4
バルブ本体
作動停止システムで構成され、オブチュレーター、シート、ステムまたはシャフト、およびパッキンシールを含み、該当する場合は PE パイプ/継手に接続するための終端を提供するバルブの主要部分。
3.1.5
操作装置
バルブの開閉を可能にする操作キーと接続するバルブの一部。
3.2 デザインに関する用語
3.2.1
フルボアバルブ
本体エンドポートの呼び内径に相当する流量断面の 80% 以上の流量断面を持つバルブ
[出典:EN 736-3:2008]
3.2.2
クリアウェイバルブ
遮るもののない流路を持つように設計されたバルブで、本体エンドポートの公称内径以上の直径を持つ理論上の球体の通過を可能にします。
[出典:EN 736-3:2008]
3.2.3
レデュースボアバルブ
本体エンドポートの公称内径に相当する流量断面の 36% 以上の流量断面を有し、フルボアバルブには対応しないバルブ
[出典:EN 736-3:2008]
参考文献
| 1 | ISO/TS 10839, 気体燃料供給用のポリエチレンパイプおよび継手 — 設計、取り扱い、設置に関する実践規範 |
| 2 | CEN/TS 1555-7, 気体燃料供給用プラスチック配管システム - ポリエチレン (PE) - Part 7: 適合性評価に関するガイダンス |
| 3 | ISO 5210, 工業用バルブ — マルチターン バルブ アクチュエータ アタッチメント |
| 4 | ISO 12176-4, プラスチックパイプおよび継手 — ポリエチレンシステムを融着接合するための機器 — Part 4: トレーサビリティコーディング |
| 5 | ISO 12176-5, プラスチックのパイプおよび継手 — ポリエチレン システムを融着接続するための機器 — Part 5: コンポーネントの 2 次元データ コーディングおよび PE 配管システムのデータ交換フォーマット |
| 6 | EN 736-3:2008, バルブ — 用語 — Part 3: 用語の定義 |
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 4437-1, EN 736-1, EN 736-2 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
3.1 General
3.1.1
external leaktightness
leaktightness of the valve body enveloping the space containing the gas, with respect to the atmosphere
3.1.2
internal leaktightness
leaktightness between the inlet and the outlet of the valve, with the valve in the closed position
3.1.3
leakage
emission of gas from a valve body, or any component of a valve
3.1.4
valve body
main part of a valve which consists of an operating stop system and contains the obturator, seat(s), stem(s) or shaft(s) and packing seals, and provides the terminal ends for connection to the PE pipe/fittings as applicable
3.1.5
operating device
part of a valve for connection with the operating key which allows the opening and the closing of the valve
3.2 Terms relating to design
3.2.1
full bore valve
valve with a flow section equal to or greater than 80 % of the section corresponding to the nominal inside diameter of the body end port
[SOURCE:EN 736-3:2008]
3.2.2
clearway valve
valve designed to have an unobstructed flow way, which allows for the passage of a theoretical sphere with a diameter that is not less than the nominal inside diameter of the body end port
[SOURCE:EN 736-3:2008]
3.2.3
reduced bore valve
valve with a flow section equal to or greater than 36 % of the section corresponding to the nominal inside diameter of the body end port and which does not correspond to the full bore valve
[SOURCE:EN 736-3:2008]
Bibliography
| 1 | ISO/TS 10839, Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| 2 | CEN/TS 1555-7, Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| 3 | ISO 5210, Industrial valves — Multi-turn valve actuator attachments |
| 4 | ISO 12176-4, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 4: Traceability coding |
| 5 | ISO 12176-5, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 5: Two-dimensional data coding of components and data exchange format for PE piping systems |
| 6 | EN 736-3:2008, Valves — Terminology — Part 3: Definition of terms |