この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
3 用語と定義
この文書の目的のために、ISO 1382 の用語と定義、および次の用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
国際ゴム硬度
IRHD
「0」はヤング率がゼロの材料の硬度を表し、「100」はヤング率が無限大の材料の硬度を表すように選択された硬度スケール。
- a) 1 つの国際ゴム硬度は、ヤング率におけるほぼ同じ比例差を常に表します。
- b)高弾性ゴムの場合、IRHD スケールと Shore A スケールは同等です。
3.2
標準硬度
指定された最小横寸法以上の標準厚さの試験片について、方法 N, H, L, および M に記載された手順を使用して得られた硬さ
注記 1:標準硬度は、IRHD で最も近い整数で報告されます。
3.3
見かけの硬さ
非標準寸法の試験片について方法 N, H, L, および M に記載されている手順を使用して取得した硬度、および方法 CN, CH, CL, および CM を使用して取得した硬度値
注記 1:見かけの硬度は、IRHD で最も近い整数で報告されます。
注記 2: CN, CH, CL, および CM の方法で得られた値は、常に見かけの硬度として与えられます。これwhere 、試験は通常、ゴムの厚さが変化する完成品に対して行われ、多くの場合、横方向の寸法が異なるためです。エッジ効果を排除するために必要な圧子とエッジ間の最小距離が提供されない可能性があります。したがって、得られた測定値は、方法 N, H, L, M で定義された標準試験片、または物品と同じ厚さの平らな平行面スラブで得られた測定値と一般に一致しません。さらに、測定値は、物品の支持方法と押え金が使用されているかどうかに大きく依存する可能性があります。したがって、曲面で得られた結果は、1 つの特定の形状および特定の寸法の試験片または物品にのみ適用できる任意の値であり、1 つの特定の方法でサポートされており、極端な場合には、そのような値は基準硬度と異なる場合があります。 10 IRHD ほど。さらに、布の跡などを除去するためにバフ研磨またはその他の方法で処理された表面は、滑らかな成形仕上げの表面とはわずかに異なる硬度値を与える可能性があります。
参考文献
| 1 | ISO 48-1, ゴム、加硫または熱可塑性プラスチック — 硬度の測定 — Part 1: 概要とガイダンス |
| 2 | ISO 48-4, ゴム、加硫または熱可塑性プラスチック — 硬度の測定 — Part 4: デュロメーター法による押し込み硬度 (ショア硬度) |
| 3 | ISO 48-5, ゴム、加硫または熱可塑性プラスチック — 硬度の測定 — Part 5: IRHD ポケットメーター法による押し込み硬度 |
| 4 | ISO 48-6, ゴム、加硫または熱可塑性プラスチック — 硬度の測定 — Part 6: IRHD 法によるゴム被覆ローラーの見かけの硬度 |
| 5 | ISO 48-7, ゴム、加硫または熱可塑性プラスチック — 硬度の測定 — Part 7: ショアタイプデュロメーター法によるゴム被覆ローラーの見かけの硬度 |
| 6 | ISO 48-8, ゴム、加硫または熱可塑性プラスチック — 硬度の決定 — Part 8: ピューシーおよびジョーンズ法によるゴムで覆われたローラーの見かけの硬度 |
| 7 | ISO 7743, ゴム、加硫または熱可塑性プラスチック — 圧縮応力-ひずみ特性の決定 |
| 8 | ISO/TR 9272:2005, ゴムおよびゴム製品 — 試験方法規格の精度の決定 |
| 9 | ISO 19983, ゴム - 試験方法の精度の決定 |
| 10 | スコット、J.R.ゴムの物理試験。マクラーレン・アンド・サンズ、ロンドン、1965 |
3 Terms and definitions
For the purposes of this document, terms and definitions in ISO 1382 and the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
international rubber hardness degrees
IRHD
hardness scale chosen so that “0” represents the hardness of material having a Young’s modulus of zero and “100” represents the hardness of a material of infinite Young’s modulus
- a) one international rubber hardness degree always represents approximately the same proportional difference in Young's modulus;
- b) for highly elastic rubbers, the IRHD and Shore A scales are comparable.
3.2
standard hardness
hardness obtained using the procedures described in methods N, H, L and M on test pieces of the standard thickness and not less than the minimum lateral dimensions specified
Note 1 to entry: Standard hardness is reported to the nearest whole number in IRHD.
3.3
apparent hardness
hardness obtained using the procedures described in methods N, H, L and M on test pieces of non-standard dimensions, as well as hardness values obtained using methods CN, CH, CL and CM
Note 1 to entry: Apparent hardness is reported to the nearest whole number in IRHD.
Note 2 to entry: Values obtained by methods CN, CH, CL and CM are always given as apparent hardnesses since tests are commonly made on the complete article where the thickness of the rubber can vary and, in many cases, the lateral dimensions might not provide the minimum distance between the indentor and the edge necessary to eliminate edge effects. Thus the readings obtained do not in general coincide with readings obtained on standard test pieces as defined in methods N, H, L and M or on a flat parallel-faced slab of the same thickness as the article. Moreover, the readings might depend appreciably on the method of support of the article and whether or not a presser foot is used. Therefore, results obtained on curved surfaces are arbitrary values applicable only to test pieces or articles of one particular shape and of particular dimensions, and supported in one particular way, and in extreme cases such values can differ from the standard hardness by as much as 10 IRHD. Furthermore, surfaces that have been buffed or otherwise prepared to remove cloth markings, etc., can give slightly different hardness values from those with a smooth, moulded finish.
Bibliography
| 1 | ISO 48-1, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 1: Introduction and guidance |
| 2 | ISO 48-4, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 4: Indentation hardness by durometer method (Shore hardness) |
| 3 | ISO 48-5, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 5: Indentation hardness by IRHD pocket meter method |
| 4 | ISO 48-6, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 6: Apparent hardness of rubber-covered rollers by IRHD method |
| 5 | ISO 48-7, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 7: Apparent hardness of rubber-covered rollers by Shore-type durometer method |
| 6 | ISO 48-8, Rubber, vulcanized or thermoplastic — Determination of hardness — Part 8: Apparent hardness of rubber-covered rollers by Pusey and Jones method |
| 7 | ISO 7743, Rubber, vulcanized or thermoplastic — Determination of compression stress-strain properties |
| 8 | ISO/TR 9272:2005, Rubber and rubber products — Determination of precision for test method standards |
| 9 | ISO 19983, Rubber — Determination of precision of test methods |
| 10 | Scott, J.R. Physical Testing of Rubbers. Maclaren and Sons, London, 1965 |