※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令で指定された規則に従って起草されます。 2.
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
このドキュメントの一部の要素が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
ISO 5771 は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 1, ホース (ゴムおよびプラスチック)によって作成されました。
この第 3 版は、技術的に改訂された第 2 版 (ISO 5771:1994) を取り消して置き換えるものです。主な変更点は、同心度要件の追加 (6.3 を参照)、ライニングとカバーの接着要件の増加 (表 4 を参照)、およびより詳細なカバー ピン刺し要件 (5.3 を参照) です。また、技術正誤表 ISO 5771:1994/Cor.1:1995 も組み込まれています。
警告 — この国際規格を使用する人は、通常の実験室の慣行に精通している必要があります。この規格は、その使用に関連するすべての安全上の問題に対処することを目的としていません。適切な健康および安全慣行を確立し、国内の規制条件を確実に遵守することは、ユーザーの責任です。
注意 — 無水アンモニアとその供給システムを取り扱うすべての担当者は、人身傷害や物的損害の可能性を最小限に抑えるために必要な安全対策を熟知し、それを利用する必要があります。無水アンモニア ホース アセンブリは、ホース メーカーが推奨する以上の温度または圧力で使用しないでください。無水アンモニアホースを再接続しないでください。この仕様に従って製造されたホースは、無水アンモニアのみでの使用に適しています。
1 スコープ
この国際規格は、-40 °C から +55 °C までの周囲温度で、液体または気体のアンモニアを移送するために使用されるゴム製ホースの最小要件を指定しています。エンド フィッティングの仕様は含まれていませんが、ホースおよびホース アセンブリの性能に限定されます。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 37, ゴム、加硫または熱可塑性 — 引張応力-ひずみ特性の測定
- ISO 188:2007, ゴム、加硫または熱可塑性 - 加速老化および耐熱性試験
- ISO 1307, ゴムおよびプラスチック ホース — ホースのサイズ、最小および最大内径、および切断された長さのホースの公差
- ISO 1402, ゴムおよびプラスチックホースおよびホースアセンブリ - 静水圧試験
- ISO 4671, ゴムおよびプラスチックホースおよびホースアセンブリ - ホースの寸法およびホースアセンブリの長さの測定方法
- ISO 4672:1997, ゴムおよびプラスチック ホース — 環境温度以下の柔軟性試験
- ISO 7326, ゴムおよびプラスチックホース - 静的条件下での耐オゾン性の評価
- ISO 8033, ゴムおよびプラスチックホース - コンポーネント間の接着の測定
- ISO 8330, ゴムおよびプラスチックホースおよびホースアセンブリ — 語彙
3 用語と定義
このドキュメントの目的のために、ISO 8330 に記載されている用語と定義が適用されます。
参考文献
| [1] | ISO 8331, ゴムおよびプラスチックホースおよびホースアセンブリ - 選択、保管、使用、およびメンテナンスに関するガイドライン |
| [2] | ISO/TR 17784, ゴムおよびプラスチックのホースおよびホース アセンブリ — 購入者、組み立て業者、設置業者、および操作担当者が使用するためのガイド |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 5771 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics).
This third edition cancels and replaces the second edition (ISO 5771:1994), which has been technically revised. The main changes are the addition of a concentricity requirement (see 6.3), increases in the lining and cover adhesion requirements (see Table 4) and more detailed cover pin-pricking requirements (see 5.3). It also incorporates the Technical Corrigendum ISO 5771:1994/Cor.1:1995.
WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions.
CAUTION — All personnel working with anhydrous ammonia and its delivery systems should be familiar with and utilize the necessary safety precautions to minimize the potential for personal injury and property damage. Do not use anhydrous-ammonia hose assemblies at temperatures or pressures above those recommended by the hose manufacturer. Never recouple an anhydrous-ammonia hose. Hoses manufactured to this specification are suitable for use with anhydrous ammonia only.
1 Scope
This International Standard specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from -40 °C up to and including +55 °C. It does not include specifications for end fittings, but is limited to the performance of the hoses and hose assemblies.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
- ISO 188:2007, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
- ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
- ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
- ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
- ISO 4672:1997, Rubber and plastics hoses — Sub-ambient temperature flexibility tests
- ISO 7326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions
- ISO 8033, Rubber and plastics hoses — Determination of adhesion between components
- ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
Bibliography
| [1] | ISO 8331, Rubber and plastics hoses and hose assemblies — Guidelines for selection, storage, use and maintenance |
| [2] | ISO/TR 17784, Rubber and plastics hoses and hose assemblies — Guide for use by purchasers, assemblers, installers and operating personnel |