この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
国際規格は、ISO/IEC 指令で指定された規則に従って起草されます。 2.
技術委員会の主な任務は、国際規格を準備することです。技術委員会によって採択されたドラフト国際規格は、投票のためにメンバー団体に配布されます。国際規格として発行するには、投票するメンバー団体の少なくとも 75% による承認が必要です。
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。
ISO 6807 は、技術委員会 ISO/TC 45, ゴムおよびゴム製品、小委員会 SC 1, ホース (ゴムおよびプラスチック)によって作成されました。
この第 2 版は、技術的に改訂された第 1 版 (ISO 6807:1984) を取り消して置き換えるものです。
序章
石油のロータリー掘削では、流体泥が高圧で大量にポンプで掘削ヘッドに送り込まれます。高圧ホースは、マッド供給回路のフレキシブル コネクタとして使用されます。
スタンドパイプの上部と垂直方向の移動を可能にするスイベルとの間に回転式掘削ホースが使用されます。また、はしけと沖合の掘削リグの間でも使用され、通常は 13.5 m を超える長さです。
回転バイブレータ ホースはより短く (9 m 以下)、ポンプとデリックまたは直立管マニホルドの間で使用され、ずれに対応し、振動を分離します。
警告 — この国際規格を使用する人は、通常の実験室の慣行に精通している必要があります。この規格は、その使用に関連するすべての安全上の問題に対処することを目的としていません。適切な健康および安全慣行を確立し、国内の規制条件を確実に遵守することは、ユーザーの責任です。
1 スコープ
この国際規格は、最大温度 82 °C までの水ベースおよび/または油ベースの泥で使用するための繊維および鋼で補強されたゴム ホースおよびホース アセンブリの要件を指定します。 ISO 2977 に準拠して試験した場合、最小アニリン点が 66 °C であるロータリー掘削サービスのボリューム。
この国際規格は、購入者の要求に応じて補足要件によって変更されない限り、- 20 °C から + 52 °C の周囲温度での使用に適しており、経年変化や熱帯条件に耐性のあるホースに適用されます。
この国際規格は、ガスでの使用を意図したホースには適用されません。
2 参考文献
本書の適用には、以下の参考文献が不可欠です。日付のある参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 37, ゴム、加硫または熱可塑性 — 引張応力-ひずみ特性の測定
- ISO 188, ゴム、加硫または熱可塑性 — 加速老化および耐熱性試験
- ISO 1402:1994, ゴムおよびプラスチックホースおよびホースアセンブリ - 静水圧試験
- ISO 1431-1, ゴム、加硫または熱可塑性 — オゾン分解に対する耐性 — 1: 静ひずみ試験
- ISO 1746:1998, ゴムまたはプラスチックのホースおよびチューブ - 曲げ試験
- ISO 1817, ゴム、加硫 — 液体の影響の測定
- ISO 2977, 石油製品および炭化水素溶剤 — アニリン点および混合アニリン点の測定
- ISO 4649:2002, ゴム、加硫または熱可塑性 — 回転円筒ドラム装置を使用した耐摩耗性の測定
- ISO 4671, ゴムおよびプラスチックホースおよびホースアセンブリ - 寸法の測定方法
- ISO 7233:1991, ゴムおよびプラスチックホースおよびホースアセンブリ - 吸引抵抗の決定
- ISO 8330, ゴムおよびプラスチックホースおよびホースアセンブリ — 語彙
- ISO 8331, ゴムおよびプラスチックホースおよびホースアセンブリ - 選択、保管、使用、およびメンテナンスのガイド
- ISO 10422, 石油および天然ガス産業 - ケーシング、チューブ、およびラインパイプのねじ山のねじ切り、ゲージング、およびねじ山検査 - 仕様
3 用語と定義
このドキュメントの目的のために、ISO 8330 に記載されている用語と定義が適用されます。
参考文献
| [1] | ISO 14693, 石油および天然ガス産業 — 掘削および井戸整備機器 |
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, 2.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6807 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics).
This second edition cancels and replaces the first edition (ISO 6807:1984), which has been technically revised.
Introduction
In rotary drilling for oil, fluid muds are pumped at high pressure in large volumes to drill heads. High-pressure hoses are used as flexible connectors in the mud supply circuit.
Rotary drilling hoses are used between the top of the standpipe and the swivel that allows vertical travel. They are also used between barges and offshore drilling rigs, usually in lengths greater than 13,5 m.
Rotary vibrator hoses are shorter (9 m or less) and used between the pump and the derrick or standpipe manifolds to accommodate misalignment and to isolate vibration.
WARNING — Persons using this International Standard should be familiar with normal laboratory practice. This standard does not purport to address all the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any national regulatory conditions.
1 Scope
This International Standard specifies the requirements for textile- and steel-reinforced rubber hoses and hose assemblies for use with water-based and/or oil-based muds, up to a maximum temperature of 82 °C, which are pumped at high pressure in large volumes in rotary drilling service and which, when tested in accordance with ISO 2977, have a minimum aniline point of 66 °C.
This International Standard applies to hoses which are suitable for use at ambient temperatures between − 20 °C and + 52 °C, unless changed by a supplementary requirement on request of the purchaser, and are resistant to ageing and tropical conditions.
This International Standard does not apply to hoses which are intended for use with gases.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
- ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
- ISO 1402:1994, Rubber and plastics hoses and hose assemblies — Hydrostatic testing
- ISO 1431-1, Rubber, vulcanized or thermoplastic — Resistance to ozone cracking — 1: Static strain test
- ISO 1746:1998, Rubber or plastics hoses and tubing — Bending tests
- ISO 1817, Rubber, vulcanized — Determination of the effects of liquids
- ISO 2977, Petroleum products and hydrocarbon solvents — Determination of aniline point and mixed aniline point
- ISO 4649:2002, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
- ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of dimensions
- ISO 7233:1991, Rubber and plastics hoses and hose assemblies — Determination of suction resistance
- ISO 8330, Rubber and plastics hoses and hose assemblies — Vocabulary
- ISO 8331, Rubber and plastics hoses and hose assemblies — Guide to selection, storage, use and maintenance
- ISO 10422, Petroleum and natural gas industries — Threading, gauging, and thread inspection of casing, tubing and line pipe threads — Specification
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 8330 apply.
Bibliography
| [1] | ISO 14693, Petroleum and natural gas industries — Drilling and well-servicing equipment |