この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
1 スコープ
この国際規格は、私設統合サービス ネットワーク (PISN) 内で相互に接続された私設統合サービス ネットワーク交換 (PINX) 間の Q 基準点での料金通知補足サービス (SS-AOC) をサポートするためのシグナリング プロトコルを指定します。
SS-AOC は、ユーザーが PISN を出て別のネットワークに入る通話の課金に関する情報を受信できるようにする一連の補助サービスです。
3 つの AOC 補足サービスは次のとおりです。
- a)呼設定時の課金情報 (AOC-S)SS-AOC-S を使用すると、ユーザーは通話のセットアップ時に課金レートに関する情報を受け取ることができ、通話中に課金レートが変更された場合にさらに情報を受け取ることもできます。
- b)通話中の課金情報 (AOC-D)SS-AOC-D を使用すると、ユーザーは通話のアクティブ フェーズ中に記録された通話料金に関する情報を受け取ることができます。
- c)通話終了時の課金情報 (AOC-E)SS-AOC-E を使用すると、ユーザーは、通話が終了したときに記録された通話料金に関する情報を受け取ることができます。
Q 基準点は、ISO/IEC 11579-1 で定義されています。
サービス仕様は、ETS 300 387 で指定された方法に従って 3 段階で作成されます。この国際規格には、Q 基準点のステージ 3 仕様が含まれており、ISO/IEC 15049 のステージ 1 およびステージ 2 仕様によって識別される要件を満たしています。
SS-AOC のシグナリング プロトコルは、ISO/IEC 11572 で指定されているように、基本的な回線交換呼制御のシグナリング プロトコルの上で動作し、ISO/IEC 11582 で指定されている補足サービスを制御するための一般的な手順の特定の側面を使用します。
この国際規格は、SS-AOC とその他の補足サービスおよび ANF との間の Q 基準点での相互作用をサポートするための追加のシグナリング プロトコル要件も指定します。
注 — Q 基準点でのシグナリング プロトコルに影響を与えない追加の相互作用は、関連するステージ 1 仕様に記載されています。
この国際規格は、相互接続して PISN を形成できる PINX に適用されます。
1 Scope
This International Standard specifies the signalling protocol for the support of the Advice Of Charge supplementary services (SS-AOC) at the Q reference point between Private Integrated services Network exchanges (PINX) connected together within a Private Integrated Services Network (PISN).
SS-AOC is a set of supplementary services which enable a user to receive information about the charging of its calls that leave the PISN and enter another network.
The three AOC supplementary services are:
- a) Charging information at call set-up time (AOC-S)SS-AOC-S enables the user to receive information about the charging rates at call set-up time and also to receive further information during the call if there is a change of charging rates.
- b) Charging information during the call (AOC-D)SS-AOC-D enables a user to receive information on the recorded charges for a call during the active phase of the call.
- c) Charging information at the end of the call (AOC-E)SS-AOC-E enables a user to receive information on the recorded charges for a call when the call is terminated.
The Q reference point is defined in ISO/IEC 11579-1.
Service specifications are produced in three stages and according to the method specified in ETS 300 387. This International Standard contains the stage 3 specification for the Q reference point and satisfies the requirements identified by the stage 1 and stage 2 specifications in ISO/IEC 15049.
The signalling protocol for SS-AOC operates on top of the signalling protocol for basic circuit switched call control, as specified in ISO/IEC 11572, and uses certain aspects of the generic procedures for the control of supplementary services specified in ISO/IEC 11582.
This International Standard also specifies additional signalling protocol requirements for the support of interactions at the Q reference point between SS-AOC and other supplementary services and ANFs.
NOTE — Additional interactions that have no impact on the signalling protocol at the Q reference point can be found in the relevant stage 1 specifications.
This International Standard is applicable to PINXs which can interconnect to form a PISN.