※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質の説明、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、 www.iso.org/iso/foreword.html を参照してください。
この文書は ISO/TC 6 技術委員会「紙、板紙、パルプ」によって作成されました。
この第 3 版は、マイナー リビジョンを構成する第 2 版 (ISO 11093-9:2006) を廃止し、置き換えるものです。
前版と比較した変更点は以下の通りです。
- コアの壁厚が 5 mm 未満の場合、破断点は検出できないという注記がスコープに追加されました。
ISO 11093 シリーズのすべての部品のリストは、ISO の Web サイトでご覧いただけます。
1 スコープ
ISO 11093 のこの部分では、巻かれた紙と板紙のコアの最大平坦圧潰抵抗を決定する方法が規定されています。
注コアの肉厚が 5 mm 未満の場合、破断点は検出できません。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 7500-1, 金属材料 — 静的一軸試験機の校正および検証 — Part 1: 引張/圧縮試験機 — 力測定システムの校正および検証
- ISO 11093-1, 紙および板紙 — コアの試験 — Part 1: サンプリング
- ISO 11093-2, 紙および板紙 — コアの試験 — Part 2: 試験サンプルの調整
3 用語と定義
この文書の目的上、次の用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
耐フラットクラッシュ性
荷重変形曲線の破砕力の最初の最大値または横ばいとなる試験片の軸に対して直角に作用する荷重から計算される量
注記 1:扁平圧壊抵抗は、キロニュートン/メートルで表されます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 6, Paper, board and pulps.
This third edition cancels and replaces the second edition (ISO 11093-9:2006), of which it constitutes a minor revision.
The changes compared to the previous edition are as follows:
- A note has been added to the scope, stating that if the wall thickness of the core is less than 5 mm, the breaking point is not detectable.
A list of all parts in the ISO 11093 series can be found on the ISO website.
1 Scope
This part of ISO 11093 specifies a method for the determination of the maximum flat crush resistance of wound paper and board cores.
NOTE If the wall thickness of the core is less than 5 mm, the breaking point is not detectable.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 7500-1, Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Calibration and verification of the force-measuring system
- ISO 11093-1, Paper and board — Testing of cores — Part 1: Sampling
- ISO 11093-2, Paper and board — Testing of cores — Part 2: Conditioning of test samples
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1
flat crush resistance
quantity calculated from the load acting at right angles to the axis of the test piece at the first maximum or levelling off of the crushing force of the load deformation curve
Note 1 to entry: The flat crush resistance is expressed in kilonewtons per metre.