この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 75-2:2013, プラスチック — 荷重下でのたわみ温度の決定 — Part 2: プラスチックとエボナイト
- ISO 178:2010+A1:2013, プラスチック - 曲げ特性の測定
- ISO 899-2:2003, プラスチック — クリープ挙動の決定 — Part 2: 3 点荷重による曲げクリープ
- ISO 3126, プラスチック配管システム - プラスチック部品 - 寸法の決定
- ISO 4435, 非加圧地下排水および下水用プラスチック配管システム — 非可塑化ポリ塩化ビニル (PVC-U)
- ISO 7684, プラスチック配管システム — ガラス強化熱硬化性プラスチック (GRP) パイプ — 乾燥条件下でのクリープ係数の決定
- ISO 7685:1998, プラスチック配管システム — ガラス強化熱硬化性プラスチック (GRP) パイプ — 初期比リング剛性の決定
- ISO 8513:2016, プラスチック配管システム — ガラス強化熱硬化性プラスチック (GRP) パイプ — 初期縦方向引張強さを測定するための試験方法
- ISO 8773, 非加圧地下排水および下水用プラスチック配管システム — ポリプロピレン (PP)
- ISO 10467:— 1 、圧力の有無にかかわらず、排水および下水用のプラスチック配管システム — 不飽和ポリエステル樹脂 (UP) をベースとしたガラス強化熱硬化性プラスチック (GRP) — パイプ、継手およびジョイントの仕様
- ISO 10468, ガラス強化熱硬化性プラスチック (GRP) パイプ - 湿潤条件下での長期固有リング クリープ剛性の決定と湿潤クリープ係数の計算
- ISO 10928:2016, プラスチック配管システム — ガラス強化熱硬化性プラスチック (GRP) のパイプと継手 — 回帰分析の方法とその使用
- ISO 10952, プラスチック配管システム — ガラス強化熱硬化性プラスチック (GRP) のパイプと継手 — たわんだ状態のセクション内部の化学攻撃に対する耐性の測定
- ISO 11296-1:2018, 地下非圧力排水および下水道ネットワークの改修のためのプラスチック配管システム — Part 1: 一般
- ISO 13002, 炭素繊維 — フィラメント糸の指定システム
- ISO 14125:1998+A1:2011, 繊維強化プラスチック複合材料 — 曲げ特性の測定
- EN 14364:2013, 加圧または加圧なしの排水および下水用のプラスチック配管システム。不飽和ポリエステル樹脂 (UP) をベースとしたガラス強化熱硬化性プラスチック (GRP)パイプ、継手、継手の仕様
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 75-2:2013, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
- ISO 178:2010+A1:2013, Plastics — Determination of flexural properties
- ISO 899-2:2003, Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
- ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
- ISO 4435, Plastics piping systems for non-pressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U)
- ISO 7684, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the creep factor under dry conditions
- ISO 7685:1998, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial specific ring stiffness
- ISO 8513:2016, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
- ISO 8773, Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP)
- ISO 10467:— 1 , Plastics piping systems for drainage and sewerage with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Specifications for pipes, fittings and joints
- ISO 10468, Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
- ISO 10928:2016, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
- ISO 10952, Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition
- ISO 11296-1:2018, Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 1: General
- ISO 13002, Carbon fibre — Designation system for filament yarns
- ISO 14125:1998+A1:2011, Fibre-reinforced plastic composites — Determination of flexural properties
- EN 14364:2013, Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints