この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
3 用語、定義、記号
3.1 用語と定義
この文書の目的上、EN 1997-1 および EN 1537 に記載されている用語と定義、および以下が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1.1
受け入れテスト
個々のアンカーが合格基準に適合していることを確認するための荷重テスト
注記 1: EN 1997-1 を参照。
3.1.2
アンカー腱抵抗性
アンカー腱の極限引張抵抗
3.1.3
臨界クリープ荷重
「 α対負荷図」の最初の擬似線形部分の終わりに対応する負荷
注記 1: 臨界クリープ荷重の決定については、付録 C を参照してください。
3.1.4
地質工学的極限状態抵抗
地面とグラウトの界面の極限抵抗または引き抜き抵抗
注記 1:地盤とグラウトの界面抵抗は、クリープ速度 α が特定のクリープ速度αULSまたはクリープ速度対荷重曲線の垂直漸近線 (つまり、無限クリープ速度)
注記 2:試験方法 2 では、クリープ速度の代わりに負荷損失が基準として使用されます。EN 1997-1 を参照してください。
3.1.5
保守限界状態耐性
クリープ速度α が特定のクリープ速度αSLSの形式で制限基準を満たすときの荷重
注記 1: 臨界クリープ荷重と呼ばれる、クリープ速度対荷重曲線上の特性点 (ニー点) に対応する荷重としても定義されます。
注記 2: EN 1997-1 を参照。
3.1.6
調査テスト
アンカーの地盤工学的な極限抵抗を確立し、使用荷重範囲でのアンカーの特性を決定するための荷重試験
注記 1: EN 1997-1 を参照。
3.1.7
プロダクションアンカー
アンカー構造の一部を形成するアンカー
注記 1:ワーキングアンカーとも呼ばれます。
注記 2:調査テストには適していません。
3.1.8
耐荷重
特定の荷重試験でアンカーが受ける最大試験荷重
3.1.9
適性検査
特定のアンカー設計が特定の地盤条件で適切であることを確認するための荷重試験
注記 1: EN 1997-1 を参照。
3.1.10
テストアンカー
テスト目的のみに設置された犠牲アンカー
3.2 記号
| A t | アンカー腱の断面積 |
| E t | アンカー腱の弾性率 |
| f | P p に対する摩擦損失の割合 |
| f tk | 特性引張強さ、EN 1993 ではf uk も呼ばれます (すべての部品) |
| f t0.1k | 0.1% 降伏ひずみに対応する特性降伏応力 = f yk |
| f t0.2k | 0.2% 降伏ひずみに対応する特性降伏応力 = f yk |
| k l | 負荷損失 |
| k ;ULS | 指定された期間にわたる荷重の許容累積損失。アンカーの極限状態の抵抗を決定するために使用されます。 |
| k ;SLS | 指定された期間にわたる荷重の許容累積損失。アンカーの保守限界状態抵抗を決定するために使用されます。 |
| L アプリ | 見かけの腱自由長 |
| L ce | 圧縮要素の長さ (EN 1537 を参照) |
| L e | アンカーヘッドの腱固定部からストレスジャッキの固定点まで測定した腱の外長 (EN 1537 を参照) |
| L 固定 | 固定アンカー長さ |
| L フリー | フリーアンカー長さ |
| L _ | 腱結合長さ |
| L tf | 腱の自由長 |
| P a | データロード |
| P c | 臨界クリープ荷重 |
| P o | アンカーロックオフ荷重 |
| P p | 耐荷重 |
| R :m | 最終限界状態基準に適合するアンカーの地盤工学的抵抗の測定値 |
| R SLS:m | 使用限界状態の基準に適合するアンカーの地盤工学的抵抗の測定値 |
| s | 腱端の変位 |
| t | 時間 |
| α | 「クリープ変位対時間の十進対数」プロットの傾き、クリープ速度、クリープ変位速度 |
| αULS__ | ULSにおけるαの限界基準 |
| αSLS__ | SLS における α の限界基準 |
| α1__ | 試験法1によるαの限界 |
| α3__ | 試験法3によるαの限界 |
| P | 耐荷重とデータム荷重の差 |
| P f | 摩擦損失 |
| Δ s | 荷重増加によって生じた腱端の測定された変位 Δ P |
| Δs el | 耐荷重P p で測定された腱端の変位から、データム荷重P a まで除荷後の変位を差し引いた値 |
参考文献
| 1 | ISO 14688-1, 地盤工学の調査と試験 — 土壌の識別と分類 — Part 1: 識別と説明 |
| 2 | EN 1992-1-5, ユーロコード 2: コンクリート構造物の設計 — Part 5: 一般規則 — 境界のない外部プレストレス腱を備えた構造 |
| 3 | EN 1993-1-1:2005+AC:2009, ユーロコード 3: 鉄骨構造の設計 — Part 1-1: 建築に関する一般規則と規則 |
| 4 | EN 1993-5, ユーロコード 3: 鋼構造物の設計 - Part 5: 杭打ち |
| 5 | EN 10080, コンクリート補強用鋼 — 溶接可能な鉄筋 — 一般 |
| 6 | EN 10138, プレストレス鋼 (すべての部品) |
3 Terms, definitions and symbols
3.1 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 1997-1 and EN 1537 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
3.1.1
acceptance test
load test to confirm that an individual anchor conforms with its acceptance criteria
Note 1 to entry: Refer to EN 1997-1.
3.1.2
anchor tendon resistance
ultimate tensile resistance of the anchor tendon
3.1.3
critical creep load
load corresponding to the end of the first pseudo-linear part of the “α versus load diagram”
Note 1 to entry: Refer to Annex C for the determination of the critical creep load.
3.1.4
geotechnical ultimate limit state resistance
ultimate resistance of the ground-grout interface or pull-out resistance
Note 1 to entry: The ground-grout interface resistance is the load at which the creep rate α meets the limiting criterion in the form of a specific creep rate αULS or the vertical asymptote of the creep rate versus load curve, (that is an infinite creep rate).
Note 2 to entry: For Test Method 2 load loss is used as criterion instead of creep rate, refer to EN 1997-1.
3.1.5
serviceability limit state resistance
load at which the creep rate α meets the limiting criterion in the form of a specific creep rate αSLS
Note 1 to entry: Also defined as the load corresponding to a characteristic point — the knee point — on the creep rate versus load curve, termed the critical creep load.
Note 2 to entry: Refer to EN 1997-1.
3.1.6
investigation test
load test to establish the geotechnical ultimate resistance of an anchor and to determine the characteristics of the anchor in the working load range
Note 1 to entry: Refer to EN 1997-1.
3.1.7
production anchor
anchor that forms part of the anchored structure
Note 1 to entry: Also referred to as a working anchor.
Note 2 to entry: Not suitable for investigation tests.
3.1.8
proof load
maximum test load to which an anchor is subjected in a particular load test
3.1.9
suitability test
load test to confirm that a particular anchor design will be adequate in particular ground conditions
Note 1 to entry: Refer to EN 1997-1.
3.1.10
test anchor
sacrificial anchor installed for testing purposes only
3.2 Symbols
| At | Cross-sectional area of anchor tendon |
| Et | elastic modulus of anchor tendon |
| f | friction loss as a percentage of Pp |
| ftk | characteristic tensile strength, also referred to as fuk in EN 1993 (all parts) |
| ft0,1k | characteristic yield stress corresponding the 0,1 % yield strain = fyk |
| ft0,2k | characteristic yield stress corresponding the 0,2 % yield strain = fyk |
| kl | load loss |
| kl;ULS | permissible cumulative loss of load over specified time period, used to determine ultimate limit state resistance of an anchor |
| kl;SLS | permissible cumulative loss of load over specified time period, used to determine serviceability limit state resistance of an anchor |
| Lapp | apparent tendon free length |
| Lce | length of compression element (refer to EN 1537) |
| Le | external length of tendon measured from the tendon anchorage in the anchor head to the anchorage point in the stressing jack (refer to EN 1537) |
| Lfixed | fixed anchor length |
| Lfree | free anchor length |
| Ltb | tendon bond length |
| Ltf | tendon free length |
| Pa | datum load |
| Pc | critical creep load |
| Po | anchor lock-off load |
| Pp | proof load |
| RULS:m | measured value of the geotechnical resistance of an anchor complying with the ultimate limit state criteria |
| RSLS:m | measured value of the geotechnical resistance of an anchor complying with the serviceability limit state criteria |
| s | tendon end displacement |
| t | time |
| α | slope of “creep displacement vs. decimal logarithm of time” plot, creep rate, creep displacement rate |
| αULS | limit criterion of α in ULS |
| αSLS | limit criterion of α in SLS |
| α1 | limit of α by test method 1 |
| α3 | limit of α by test method 3 |
| ΔP | difference between proof load and datum load |
| ΔPf | friction loss |
| Δs | measured displacement of the tendon end produced by load increment ΔP |
| ∆sel | measured displacement of the tendon end at proof load Pp minus displacement after de-loading to datum load Pa |
Bibliography
| 1 | ISO 14688-1, Geotechnical investigation and testing — Identification and classification of soil — Part 1: Identification and description |
| 2 | EN 1992-1-5, Eurocode 2: Design of concrete structures — Part 5: General rules — Structures with unbounded and external pre-stressing tendons |
| 3 | EN 1993-1-1:2005+AC:2009, Eurocode 3: Design of steel structures — Part 1-1: General rules and rules for buildings |
| 4 | EN 1993-5, Eurocode 3: Design of steel structures — Part 5: Piling |
| 5 | EN 10080, Steel for the reinforcement of concrete — Weldable reinforcement steel — General |
| 6 | EN 10138, Prestressing steels (all parts) |