この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序章
この文書には、フラッシュなしとフラッシュ点の決定をカバーする 3 つの手順 (A, B, および C) が含まれています。迅速な平衡手順 A と B により、それぞれ引火点と引火点の決定が可能になります。非平衡手順 C では、引火点の測定に自動化されたテスト カップ温度制御が使用されます。
ISO 1516 および ISO 1523 も、方法を選択する際に考慮できるクローズド カップ平衡試験方法です。
この文書で指定された装置を使用すると、ISO 1516 または ISO 1523 で要求されているものよりも、より迅速な手順 A または B と、より小さなテスト部分 (2 ml または 4 ml) を使用して、同様のテスト結果を決定できます。このドキュメントの装置は、ラボでの通常の使用だけでなく、現場でのテストにも適しているようにポータブルにすることができます。共同作業[16]は、これらの方法で得られた結果が同等であることを示しています。手順 C は、試験方法 IP 534 [18]および ASTM D7236 [14]に基づいています。
ハロゲン化炭化水素を含む溶媒混合物で得られた引火点の結果の解釈は、これらの混合物が異常な結果をもたらす可能性があるため、注意して考慮する必要があります[17] 。
限られた研究では、この文書で電気点火器を使用すると、一部の水性塗料が引火点を上昇させる可能性があることが示されています。
引火点は、「可燃性」および「可燃性」物質を定義する分類特性として、出荷、保管、取り扱い、および安全規則で使用されます。クラスの正確な定義は、それぞれの特定の規則に記載されています。
引火点は、比較的不揮発性または不燃性の物質の中に揮発性の高い物質が存在することを示します。引火点試験は、未知の物質の組成を調査するための予備段階としてよく使用されます。
潜在的に不安定な、分解しやすい、または爆発性の物質に対して実施する引火点測定は適切ではありません。すなわち、その方法に必要な温度範囲内で、引火点装置の金属部品と接触するそのような物質の指定された量を加熱しても、分解、爆発、または他の悪影響を引き起こさないことが以前に確立されていない限り.
引火点は、試験された材料の一定の物理化学的特性ではありません。これは、装置の設計、使用される装置の状態、および実行される操作手順の機能です。したがって、引火点は標準的な試験方法によってのみ定義することができ、異なる試験方法または指定されたものとは異なる試験装置によって得られた結果の間の一般的な有効な相関関係は保証されません。
ISO/TR 29662 も、引火点試験の実施と結果の解釈に役立つアドバイスを提供しています。
警告このドキュメントの使用には、危険な物質、操作、および機器が含まれる場合があります。このドキュメントは、その使用に関連するすべての安全上の問題に対処することを意図していません。この文書のユーザーは、標準を適用する前に人員の安全と健康を確保するための適切な措置を講じ、この目的のために他の制限の適用可能性を判断する責任があります。
Introduction
This document includes three procedures (A, B and C) covering determinations of flash no-flash and flash point. Rapid equilibrium procedures A and B enable the determination of the flash no-flash and flash point, respectively. Non-equilibrium procedure C uses automated test cup temperature control for flash point determination.
ISO 1516 and ISO 1523 are also closed cup equilibrium test methods that can be considered when selecting a method.
The apparatus specified in this document enables a similar test result to be determined using more rapid procedures, A or B, and a smaller test portion (2 ml or 4 ml), than those required in ISO 1516 or ISO 1523. In addition, the apparatus in this document can be made portable so that it is suitable for on-site testing, as well as its regular use in laboratories. Collaborative work[16] has shown that results obtained by these methods are comparable. Procedure C is based on test methods IP 534[18] and ASTM D7236[14].
The interpretation of flash point results obtained on solvent mixtures containing halogenated hydrocarbons should be considered with caution, as these mixtures can give anomalous results[17].
A limited study has indicated that some water borne paints can give an elevated flash point when an electric ignitor is used with this document.
Flash point is used in shipping, storage, handling, and safety regulations, as a classification property to define “flammable” and “combustible” materials. Precise definition of the classes is given in each particular regulation.
The flash point indicates the presence of highly volatile material(s) in a relatively non-volatile or non-flammable material. Flash point testing is often used as a preliminary step to other investigations into the composition of unknown materials.
It is not appropriate for flash point determinations to be carried out on potentially unstable, decomposable, or explosive materials. That is, unless it has been previously established that heating the specified quantity of such materials in contact with the metallic components of the flash point apparatus, within the temperature range required for the method, does not induce decomposition, explosion or other adverse effects.
The flash point is not a constant physical-chemical property of a material tested. It is a function of the apparatus design, the condition of the apparatus used, and the operational procedure carried out. Flash point can therefore only be defined in terms of a standard test method, and no general valid correlation can be guaranteed between results obtained by different test methods or with test apparatus different from that specified.
ISO/TR 29662 also gives useful advice in carrying out flash point tests and interpreting results.
WARNING The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of users of this document to take appropriate measures to ensure the safety and health of personnel prior to the application of the standard, and to determine the applicability of any other restrictions for this purpose.