この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
3 用語と定義
この文書の目的としては、ISO 445 および以下に示されている用語と定義が適用されます。
ISO と IEC は、標準化に使用する用語データベースを次のアドレスで維持しています。
3.1
1つのコンポーネントの破損
パレットの強度、 剛性 (3.9) または機能に重大な影響を与える構造要素の破損
3.2
集中荷重
パレット上部デッキの 50% 未満の領域に荷重が集中する
3.3
最大使用荷重
パレットが特定の積載および支持条件で運ぶことを許可される最大 積載量 (3.5)
注記 1: これは、荷重および支持システムのタイプ、分布、配置および安定化手段によって異なり、 公称荷重 (3.4) よりも低い場合もあれば高い場合もあります (ISO 8611-2 および ISO 8611 を参照) -3)
3.4
公称荷重
R
荷重の種類に関係なく、指定された支持条件における最低 試験荷重 (3.10) の値 ( 集中荷重 (3.2) を除く)
注記 1: 「指定されたサポート条件」とは、 ISO 8611-2:2021, 7.1 の使用条件の範囲を指します。
注記 2: 公称荷重は、使用中のパレット上の実際の 積載量 (3.5) を表すものではありません。公称荷重は、さまざまなパレットの性能を比較するために使用されます。
3.5
ペイロード
Q
使用中のパレットによって運ばれる荷重
注記 1:これは、 公称荷重 (3.4) より上でも、同じでも、下でも構いません。
3.6
プラテン
サンプルパレットを試験するために荷重を加えるために使用される試験機の堅くて硬い表面
3.7
ラッキング
サポートされていない空きスパンを備えたドライブインまたはビームラックでのユニットロードの保管
3.8
積み重ねる
中間棚や ラックに頼らずに、単位荷重を積んだパレットを交互に配置すること (3.7)
3.9
剛性
荷重を受けたパレットまたはコンポーネントの相対的な変形
注記 1: 高い剛性とは、所定の荷重に対する変位、たわみ、または変形が小さいことを意味します。
3.10
テストロード
P
荷重アプリケーター、荷重ボードまたは荷重ボックス、およびデータム荷重を含む適用荷重自体 ( 極限荷重 (3.11) の 1.5 % ± 0.5 %)
3.11
最終荷重
U
圧縮、変位、またはたわみが抑えられなくなり、試験片の破壊または 1 つの構成部品 (3.1) の破損を引き起こす、または変位、変形、またはたわみが過剰になったときの荷重。
注記 1: ISO 8611-2:2021, 表 1 を参照。
参考文献
| 1 | ISO 8611-3:2011, マテリアルハンドリング用パレット — フラットパレット — Part 3: 最大使用荷重 |
| 2 | ISO 3691-5, 産業用トラック — 安全要件と検証 — Part 5: 歩行者推進トラック |
| 3 | ISO 13061-1, 木材の物理的および機械的特性 — 小さな透明な木材試験片の試験方法 — Part 1: 物理的および機械的試験のための含水量の測定 |
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 445 and the following apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
3.1
breaking of one component
fracture of a structural element which significantly affects the strength, stiffness (3.9) or functionality of a pallet
3.2
concentrated load
load concentrated over an area of less than 50 % of the pallet top deck
3.3
maximum working load
greatest payload (3.5) that a pallet is permitted to carry in a specific loading and support condition
Note 1 to entry: This varies according to the type, distribution, arrangement and means of stabilization of the load and the system of support, and can be lower or higher than the nominal load (3.4) (see ISO 8611-2 and ISO 8611-3).
3.4
nominal load
R
lowest test load (3.10) value for the specified support conditions, independent of the type of load (excluding concentrated loads (3.2) )
Note 1 to entry: “Specified support conditions” refers to the range of conditions of use in ISO 8611-2:2021, 7.1.
Note 2 to entry: Nominal load does not represent an actual payload (3.5) on a pallet in use. The nominal load is used for comparing the performance of different pallets.
3.5
payload
Q
load carried by the pallet in use
Note 1 to entry: This can be above, identical to or below the nominal load (3.4) .
3.6
platen
solid, rigid surface on a test machine used for applying a load to test a sample pallet
3.7
racking
storage of unit loads in drive-in or beam racks with free, unsupported spans
3.8
stacking
placing of pallets with unit loads one upon the other without recourse to intermediate shelves or racking (3.7)
3.9
stiffness
relative deformation of a pallet or component under load
Note 1 to entry: High stiffness means small displacement, deflection or deformation for a given load.
3.10
test load
P
load applicators, the load board or load box and the applied load itself including the datum load (1,5 % ± 0,5 % of the ultimate load (3.11) )
3.11
ultimate load
U
load at which compression, displacement or deflection is no longer contained, resulting in the destruction of the specimen or breaking of one component (3.1) , or when displacement, deformation or deflection becomes excessive
Note 1 to entry: See ISO 8611-2:2021, Table 1.
Bibliography
| 1 | ISO 8611-3:2011, Pallets for materials handling — Flat pallets — Part 3: Maximum working loads |
| 2 | ISO 3691-5, Industrial trucks — Safety requirements and verification — Part 5: Pedestrian-propelled trucks |
| 3 | ISO 13061-1, Physical and mechanical properties of wood — Test methods for small clear wood specimens — Part 1: Determination of moisture content for physical and mechanical tests |