この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序章
0.1ISO/R76:1958
ISO/R 76, Ball and Roller Bearings — Methods of Evaluating Static Load Ratings は、技術委員会 ISO/TC 4, Ball and Roller Bearingsによって作成されました。
ISO/R 76 は、A. Palmgren らの研究[2], [3]に基づいています。基本静定格荷重は、転動体直径の 0.000 1 の最も大きな応力がかかる転動体/軌道面接触での転動体と軌道面の総永久変形に対応するように定義されました。次に、特別な内部設計の転がり軸受の基本静定格荷重に限定された標準値が定められました。
ISO/R 76:1958 は 28 のメンバー団体 (合計 38 のうち) によって承認され、ISO 評議会に提出され、1958 年 12 月に ISO 勧告として受け入れることが決定されました。
0.2ISO76:1978
ISO/TC 4 は、その作業計画に ISO/R 76 の改訂を含めることを決定し、ISO/TC 4/SC 8 事務局に草案の作成を依頼しました。その結果、事務局は 1976 年 1 月に草案[3]を提出した。
提案草案は、ISO/TC 4/SC 8 の 8 メンバーのうち 6 メンバーによって受け入れられました。残りの 2 メンバーのうち、日本はさらなる検討を希望し、米国は、その反対提案、文書 ISO/TC 4/SC 8 N 64 [4]を希望しました。その後、草案は ISO 中央事務局に提出されました。原案が ISO 加盟団体によって承認された後、ISO 理事会は 1978 年 6 月にそれを国際規格として受け入れることを決定しました。
ISO 76:1978 は SI 単位ニュートンを採用し、全体的に改訂されましたが、本質的な変更はありませんでした。ただし、ラジアル ボール ベアリングの静的等価ラジアル荷重を計算するために、アンギュラ コンタクト グルーブ ボール ベアリングの公称接触角 15° および 45° のX0およびY0の値が表に追加されました (ISO 76:1978 を参照)表 2 )
0.3 ISO 76:1987
ISO/R 76:1958 の改訂中、米国は 1975 年に計算された接触応力に基づく基本静定格荷重の反対提案[4]を提出しました。
事務局は、1978 年 1 月に接触応力レベルに基づく静定格荷重の改訂について採決を要請し、その後 1978 年 6 月に採決結果を回覧し、項目 No.改訂作業のNo. TC 4の作業プログラムの15
ISO/TC 4/SC 8, 文書 TC 4/SC 8 N 75 [5]および TC 4 N 865 [6]で作成された提案、ならびに TC 4 メンバーおよび複数の SC 8 メンバーによって作成されたコメントを考慮して、 ISO 76 を更新する必要性を表明し、静的定格荷重の基礎として永久変形または応力レベルのいずれかを使用する可能性を考慮して研究を継続することに同意し、ISO/TC 4/SC 8 はその事務局に新しい草案を作成するよう要請しました。 .新しい草案は、文書 TC 4/SC 8 N 75 の原理と式を使用して作成され、一般に 0.000 1 の永久変形に対応すると述べられているさまざまな転動体接触の接触応力のレベルを含めることを目的としていました。最も大きな応力がかかる転動体/レースウェイ接触の中心における転動体直径。ローラー ベアリングの場合、4 000 MPa の応力レベルが合意され、ISO/TC 4/SC 8 は多数決により、静定格荷重が次の計算された接触応力に対応する必要があることに合意しました。
| ころ軸受の場合は 4 000 MPa, | |
| 自動調心玉軸受の場合は 4 600 MPa, および | |
| 4 規格が適用されるその他すべての玉軸受については 200 MP |
これらの計算された接触応力の場合、総永久変形は、最も大きな応力がかかる転動体/軌道接触の中心で発生し、その変形は転動体直径の約 0.000 1 です。
ISO 76 は 1985 年に ISO 中央事務局に提出され、ISO メンバーによって承認された後、1987 年 2 月に ISO 理事会はそれを国際規格として受け入れることを決定しました。
さらに、ISO/TC 4/SC 8 は、ISO 76 で与えられた式と係数の導出に関する補足的な背景情報をテクニカル レポートとして公開することを決定しました。このテクニカル レポートは、ISO/TR 10657:1991 として発行されました。
ラジアル ベアリングとアキシャル ベアリング間の定格荷重の不連続性を説明する ISO 76:1987 の修正案は、ISO 76:1987/Amd.1:1999 として発行されました。
0.4 ISO 76:2006
ISO 76:1987 の系統的レビューは、事前に行われた投票プロセスとドキュメント TC 4/SC 8 N 233 および N 235 に基づいて、2003 年に合意されました。
ISO 76:2006 には、編集上の適応と更新、および静的安全係数S0による拡張が含まれています。さらに、ISO 76:1987/Amd.1:1999 が統合され、有益な付属書 A「基本静定格荷重の計算における不連続性」になりました。
0.5 ISO 76: 2006 /Amd.1:2017
ISO 76:2006/Amd.1:2017 には、次の項目が含まれます。
- 因子f0 、 X0およびY0のグラフは、ÖNORM M 6320 草案から引用され、有益な付属書に含まれます。
- ISO/TR 10657 からの定格荷重係数f0の計算式は、規格の規範部分に導入されます。
- 定格荷重係数f0の表は、規格の規範的な部分にとどまりますが、式から得られた結果が優先されることを示す文章が導入されます。
Introduction
0.1 ISO/R 76:1958
ISO/R 76, Ball and Roller Bearings — Methods of Evaluating Static Load Ratings, was drawn up by Technical Committee ISO/TC 4, Ball and Roller Bearings.
ISO/R 76 was based on the studies of A. Palmgren et al[2],[3]. The basic static load ratings were defined to correspond to a total permanent deformation of rolling element and raceway at the most heavily stressed rolling element/raceway contact of 0,000 1 of the rolling element diameter. Then the standard values confined to the basic static load ratings for special inner design rolling bearings were laid down.
ISO/R 76:1958 was approved by 28 (out of a total of 38) member bodies and was then submitted to the ISO Council, which decided, in December 1958, to accept it as an ISO Recommendation.
0.2 ISO 76:1978
ISO/TC 4 decided to include the revision of ISO/R 76 in its programme of work and ISO/TC 4/SC 8 secretariat was requested to prepare a draft proposal. As a result, the secretariat submitted a draft proposal[3] in January 1976.
The draft proposal was accepted by 6 of the 8 members of ISO/TC 4/SC 8. Of the remaining two, Japan preferred further study and USA, its counter proposal, document ISO/TC 4/SC 8 N 64[4]. The draft was then submitted to the ISO Central Secretariat. After the draft had been approved by the ISO member bodies, the ISO Council decided in June 1978 to accept it as an International Standard.
ISO 76:1978 adopted the SI unit newton and was revised in total, but without essential changes of substance. However, values of X0 and Y0 for the nominal contact angles 15° and 45° for angular contact groove ball bearings were added to the table to calculate the static equivalent radial loads of radial ball bearings (see ISO 76:1978, Table 2).
0.3 ISO 76:1987
During the revision of ISO/R 76:1958, USA had in 1975 submitted a counter proposal[4] for the basic static load ratings based on a calculated contact stress.
The secretariat requested a vote on the revision of the static load ratings based on a contact stress level in January 1978 and afterward circulated the voted results in June 1978, and the item No. of revision work had become No. 157 of the programme of work of TC 4.
ISO/TC 4/SC 8, considering the proposals made in the documents TC 4/SC 8 N 75[5] and TC 4 N 865[6], as well as the comments made by TC 4 members and that several SC 8 members expressed a need for updating ISO 76, agreed to continue its study taking into account the possibility of using either permanent deformation or stress level as a basis for static load ratings, and ISO/TC 4/SC 8 requested its secretariat to prepare a new draft. The new draft was intended to be prepared with the principles and formulae of the document TC 4/SC 8 N 75, and to include levels of contact stress for various rolling element contact stated to be generally corresponding to a permanent deformation of 0,000 1 of the rolling element diameter at the centre of the most heavily stressed rolling element/raceway contact. For roller bearings a stress level of 4 000 MPa was agreed and then ISO/TC 4/SC 8 agreed, by a majority vote, that static load ratings should correspond to calculated contact stresses of
| 4 000 MPa for roller bearings, | |
| 4 600 MPa for self‑aligning ball bearings, and | |
| 4 200 MPa for all other ball bearings to which the standard applies. |
For these calculated contact stresses, a total permanent deformation occurs at the centre of the most heavily stressed rolling element/raceway contact, and its deformation is approximately 0,000 1 of the rolling element diameter.
ISO 76 was submitted to the ISO Central Secretariat in 1985, and after it had been approved by the ISO members, the ISO Council decided in February 1987 to accept it as an International Standard.
Furthermore, ISO/TC 4/SC 8 decided that supplementary background information, regarding the derivation of formulae and factors given in ISO 76, should be published as a Technical Report. This Technical report was published as ISO/TR 10657:1991.
An Amendment to ISO 76:1987 that explains the discontinuities in load ratings between radial- and axial bearings was published as ISO 76:1987/Amd.1:1999.
0.4 ISO 76:2006
A systematic review of ISO 76:1987 was agreed in 2003, based on the prior held balloting process and documents TC 4/SC 8 N 233 and N 235.
ISO 76:2006 includes editorial adaptations and updates as well as an extension by the static safety factor S0. Furthermore, ISO 76:1987/Amd.1:1999 was integrated and became the informative Annex A “Discontinuities in the calculation of basic static load ratings”.
0.5 ISO 76: 2006 /Amd.1:2017
ISO 76:2006/Amd.1:2017 includes the following items:
- graphs for the factors f0, X0 and Y0 taken from draft ÖNORM M 6320 to be included in an informative annex;
- formulae for the calculation of the load rating factor f0 from ISO/TR 10657 to be introduced in the normative part of the standard;
- the tables for the load rating factor f0 will stay in the normative part of the standard, however a sentence will be introduced stating that the results obtained from formulae are preferred.