この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
1 スコープ
この文書では、船体の長さ ( LH ) または最大 24 m の荷重線の長さ (注を参照) のマルチハル クラフトに作用する寸法、局所的な設計圧力、および全体的な荷重を定義します。 ISO 12217 (すべての部品) に従って、安定性、乾舷、および浮力を評価する際に、水密または風雨密であると想定される航空機のすべての部品を考慮します。次に、ISO 12215-5 を使用して、局所的な設計圧力に対応する寸法を評価します。
注記積載ラインの長さは、OMI「国際積載ライン条約 1966/2005」で定義されており、オーバーハングのある船の場合、 LHより短くなる場合があります。この長さは、いくつかの IMO 条約の下限である 24 m にも設定されています。
この文書は、ISO 12215-5 と同じ材料で無傷の状態で、次の 2 つのタイプのマルチハルに適用されます。
- レクリエーションチャーター船を含むレクリエーション船;
- 商用船とワークボート。
プロのレース専用に設計されたマルチハル レーシング クラフトには適用されません。
このドキュメントは、窓、ポートライト、ハッチ、デッドライト、およびドアをサポートする構造に適用されます。
船体の完全な寸法については、この文書は、舵については ISO 12215-8, 帆船の付属物については ISO 12215-9, 帆船のリグ荷重とリグの取り付けについては ISO 12215-10 と組み合わせて使用することを意図しています。詳細については、ISO 12215-6 を使用できます。
このドキュメントでは、特に指定のない限り、寸法は (m)、面積は (m 2 )、質量は (kg)、力は (N)、モーメントは (Nm)、圧力は (kN/m 2 ) (1 kN/m2 = 1 kPa)、応力と弾性係数 (N/mm2 ) ( 1 N/mm2 = 1 MPa)
1 Scope
This document defines the dimensions, local design pressures and global loads acting on multihull craft with a hull length (LH) or load line length of up to 24 m (see Note). It considers all parts of the craft that are assumed watertight or weathertight when assessing stability, freeboard and buoyancy in accordance with ISO 12217 (all parts). Scantlings corresponding to the local design pressures are then assessed using ISO 12215-5.
NOTE The load line length is defined in the OMI"International Load Lines Convention 1966/2005", it can be smaller than LH for craft with overhangs. This length also sets up at 24 m the lower limit of several IMO conventions.
This document is applicable to multihulls built from the same materials as in ISO 12215-5, in intact condition, and of the two following types:
- recreational craft, including recreational charter vessels;
- commercial craft and workboats.
It is not applicable to multihull racing craft designed only for professional racing.
This document is applicable to the structures supporting windows, portlights, hatches, deadlights and doors.
For the complete scantlings of the craft, this document is intended to be used in conjunction with ISO 12215-8 for rudders, ISO 12215-9 for appendages of sailing craft and ISO 12215-10 for rig loads and rig attachment in sailing craft. ISO 12215-6 can be used for additional details.
Throughout this document, unless otherwise specified, dimensions are in (m), areas in (m2), masses in (kg), forces in (N), moments in (Nm), Pressures in (kN/m2) (1 kN/m2 = 1 kPa), stresses and elastic modulus in (N/mm2) (1 N/mm2 = 1 MPa).