この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、各国の標準化団体 (ISO メンバー団体) の世界的な連合です。国際規格の作成作業は、通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。 ISOと連携して、政府および非政府の国際機関もこの作業に参加しています。 ISO は、電気技術の標準化に関するすべての問題について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用された手順と、今後の維持のために意図された手順は、ISO/IEC 指令のPart 1 で説明されています。特に、さまざまな種類の ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令のPart 2 の編集規則に従って起草されました ( www.iso.org/directives を参照)
このドキュメントの要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、そのような特許権の一部または全部を特定する責任を負わないものとします。ドキュメントの開発中に特定された特許権の詳細は、序文および/または受信した特許宣言の ISO リストに記載されます ( www.iso.org/patents を参照)
このドキュメントで使用されている商号は、ユーザーの便宜のために提供された情報であり、保証を構成するものではありません。
適合性評価に関連する ISO 固有の用語および表現の意味に関する説明、および技術的貿易障壁 (TBT) における ISO の WTO 原則への準拠に関する情報については、次の URL を参照して ください 。
この文書を担当する委員会は、技術委員会 ISO/TC 39, 工作機械、小委員会 SC 10, 安全です。
この ISO 16089 の初版は、欧州規格 EN 13218:2002+A1/AC:2010-04 を採用したものです。欧州規格と ISO 16089 の主な違いは次のとおりです。
- a)自動化の程度に基づいて、研削盤を 3 つのグループに細分することの導入。研削盤のグループごとに安全設計のための具体的な安全対策。
- b)別の選択デバイスと特定の安全対策を備えた安全操作モード 3 (制限された操作条件下での手動介入のためのオプションの特別モード) の導入、および例を提供する新しい有益な付属書。
- c) EN 954-1 のカテゴリの代わりに、関連する安全機能について ISO 13849-1 に従って要求される性能レベルが定義されています。
- d)保護されていないポリカーボネートの使用期間による耐衝撃性の低下は、付属書 A の老化曲線の形で示されています。
- e)可燃性金属加工油の使用に関する措置は、新しい附属書 H に記載されています。
- f)可燃性の金属加工油を使用する場合の抽出システムと消火システムの統合の例は、新しい附属書 I に記載されています。
- g)新しい附属書 K に記載されている砥石スピンドルの回転速度制限監視の例。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is Technical Committee ISO/TC 39, Machine tools, Subcommittee SC 10, Safety.
This first edition of ISO 16089 is an adaptation of European Standard EN 13218:2002+A1/AC:2010-04. Significant differences between the European Standard and ISO 16089 are as follows.
- a) Introduction of a subdivision of grinding machines into three groups, based on the degree of automation. Specific safety measures for safe design for each group of grinding machines.
- b) Introduction of the Mode of safe operation 3 (optional special mode for manual intervention under restricted operating conditions) with a separate selection device and specific safety measures, and a new informative Annex providing examples.
- c) Instead of the categories of EN 954-1, the required performance level according to ISO 13849-1 is defined for relevant safety functions.
- d) The decrease in the impact resistance of unprotected polycarbonate depending on the duration of use is shown in the form of an aging curve in Annex A.
- e) Measures for the use of flammable metalworking fluids are given in the new Annex H.
- f) Examples for the integration of extraction and fire extinguishing systems when using flammable metalworking fluids are given in the new Annex I.
- g) Example for rotational speed limit monitoring of the wheel spindle given in the new Annex K.