この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
序文
ISO (国際標準化機構) は、国家標準化団体 (ISO メンバー団体) の世界的な連合体です。国際規格の作成作業は通常、ISO 技術委員会を通じて行われます。技術委員会が設立された主題に関心のある各会員団体は、その委員会に代表される権利を有します。政府および非政府の国際機関も ISO と連携してこの作業に参加しています。 ISO は、電気技術の標準化に関するあらゆる事項について、国際電気標準会議 (IEC) と緊密に協力しています。
この文書の作成に使用される手順と、そのさらなる保守を目的とした手順は、ISO/IEC 指令Part 1 部に記載されています。特に、さまざまなタイプの ISO 文書に必要なさまざまな承認基準に注意する必要があります。この文書は、ISO/IEC 指令Part 2 部の編集規則に従って起草されました ( www.iso.org/directives を参照)
この文書の要素の一部が特許権の対象となる可能性があることに注意してください。 ISO は、かかる特許権の一部またはすべてを特定する責任を負わないものとします。文書の作成中に特定された特許権の詳細は、序論および/または受け取った特許宣言の ISO リストに記載されます ( www.iso.org/patents を 参照)
本書で使用されている商号は、ユーザーの便宜のために提供された情報であり、推奨を構成するものではありません。
規格の自主的な性質、適合性評価に関連する ISO 固有の用語と表現の意味、および貿易技術的障壁 (TBT) における世界貿易機関 (WTO) 原則への ISO の準拠に関する情報については、 www.iso.org/iso/foreword.html を参照してください。
この文書は、技術委員会 ISO/TC 60, 歯車、小委員会 SC 2, 歯車容量計算によって作成されました。
この第 2 版は、第 1 版 (ISO 14635-3:2005) を廃止し、置き換えるものであり、そのマイナーリビジョンを構成します。変更点は次のとおりです。
- ISO 1328-1:1995 1は、この文書で ISO 1328-1:2013 の公差クラスとは数値的に異なる精度等級を使用しているため、日付が付けられています。
- ISO 4287 は廃止され、ISO 21920-2 に置き換えられました。
- 廃止された ISO 4964 の代替品であり、同様の情報は ISO 18265 にあります。
- 撤回された一部の参考文献エントリの置き換え、および日付のある参照から日付のない参照への変更。
- 表 1 の説明「ピッチ ライン速度 ( v w )」は、表現を ISO 6336 シリーズと調和させるために「ピッチ ラインでの周速度」に置き換えられています。
- 表 1 の「特定の滑り」の記号は ISO 21771 に従って修正されました。
- 表 2, 研削:「ストローク ドライブの生成」の単位が修正されました。
- 表 3 の負荷カップリングに関する情報は ISO 14635-1 と調和しています。
- 第 9 項、比減量の報告値が修正されました。
ISO 14635 シリーズのすべての部品のリストは、ISO の Web サイトでご覧いただけます。
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives ).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents ).
Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html .
This document was prepared by Technical Committee ISO/TC 60, Gears, Subcommittee SC 2, Gear capacity calculation.
This second edition cancels and replaces the first edition (ISO 14635-3:2005), of which it constitutes a minor revision. The changes are as follows:
- ISO 1328-1:1995 1 has been dated as this document uses accuracy grade which is numerically different than tolerance class in ISO 1328-1:2013;
- replacement of ISO 4287 which has been withdrawn and replaced by ISO 21920-2;
- replacement of ISO 4964 which has been withdrawn and similar information can be found in ISO 18265;
- replacement of some bibliography entries which were withdrawn, and changes from dated to undated references;
- Table 1, description"pitch line velocity (vw)" has been replaced by"circumferential velocity at the pitch line" to harmonize the wording with the ISO 6336-series;
- Table 1, symbol for"specific sliding" has been corrected according to ISO 21771;
- Table 2, grinding: unit for"generating stroke drive" has been corrected;
- Table 3, information on the load coupling has been harmonized with ISO 14635-1;
- Clause 9, the reporting value of the specific weight loss has been corrected.
A list of all parts in the ISO 14635 series can be found on the ISO website.