この規格 プレビューページの目次
※一部、英文及び仏文を自動翻訳した日本語訳を使用しています。
2 規範的参照
以下の文書は、その内容の一部またはすべてがこの文書の要件を構成する形で本文中で参照されています。日付が記載された参考文献については、引用された版のみが適用されます。日付のない参照については、参照文書の最新版 (修正を含む) が適用されます。
- ISO 179-1, プラスチック — シャルピー衝撃特性の測定 — Part 1: 計器を使用しない衝撃試験
- ISO 291, プラスチック — 調整および試験用の標準雰囲気
- ISO 472, プラスチック - 語彙
- ISO 527-2, プラスチック — 引張特性の決定 — Part 2: 成形および押出プラスチックの試験条件
- ISO 580:2005, プラスチック配管およびダクトシステム - 射出成形熱可塑性プラスチック継手 - 加熱の影響を視覚的に評価する方法
- ISO 604, プラスチック - 圧縮特性の決定
- ISO 899-2, プラスチック — クリープ挙動の決定 — Part 2: 3 点荷重による曲げクリープ
- ISO 1043-1, プラスチック — 記号と略語 — Part 1: 基本ポリマーとその特殊な特性
- ISO 1133-1, プラスチック — 熱可塑性プラスチックのメルトマスフローレート (MFR) およびメルトボリュームフローレート (MVR) の決定 — Part 1: 標準方法
- ISO 1167-1:2006, 流体輸送用の熱可塑性プラスチックのパイプ、継手およびアセンブリ — 内圧に対する耐性の測定 — Part 1: 一般的な方法
- ISO 1167-2, 流体輸送用の熱可塑性プラスチックパイプ、継手およびアセンブリ — 内圧に対する耐性の測定 — Part 2: パイプ試験片の準備
- ISO 1183-1, プラスチック — 非気泡プラスチックの密度を決定する方法 — Part 1: 浸漬法、液体ピクノメータ法および滴定法
- ISO 3126, プラスチック配管システム - プラスチック部品 - 寸法の決定
- ISO 3127, 熱可塑性プラスチックパイプ — 外部衝撃に対する耐性の決定 — 24時間体制の方法
- ISO 3451-1, プラスチック — 灰の測定 — Part 1: 一般的な方法
- ISO 9967:2016, 熱可塑性プラスチックパイプ — クリープ率の決定
- ISO 9969, 熱可塑性プラスチックパイプ - リング剛性の決定
- ISO 11357-6, プラスチック — 示差走査熱量測定 (DSC) — Part 6: 酸化誘導時間 (等温 OIT) および酸化誘導温度 (動的 OIT) の決定
- ISO/TS 28037:2010, 直線校正関数の決定と使用
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
- ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
- ISO 291, Plastics — Standard atmospheres for conditioning and testing
- ISO 472, Plastics — Vocabulary
- ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
- ISO 580:2005, Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating
- ISO 604, Plastics — Determination of compressive properties
- ISO 899-2, Plastics — Determination of creep behaviour — Part 2: Flexural creep by three-point loading
- ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
- ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method
- ISO 1167-1:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method
- ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
- ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method
- ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
- ISO 3127, Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method
- ISO 3451-1, Plastics — Determination of ash — Part 1: General methods
- ISO 9967:2016, Thermoplastics pipes — Determination of creep ratio
- ISO 9969, Thermoplastics pipes — Determination of ring stiffness
- ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
- ISO/TS 28037:2010, Determination and use of straight-line calibration functions